Daikin EHBH04CA, Руководство по установке

Страница: 14 / 28

4 Configuration
Installation manual
14
EHBH/X04~16CA
Daikin Altherma - Low Temperature Split
4P313771-1C – 2012.11
Digital I/O PCB
# Code Description
[A.2.2.6.1] [C-02] External backup heat source:
▪ 0 (No): None
▪ 1 (Bivalent): Gas, oil boiler
▪ 2: N/A
▪ 3: N/A
[A.2.2.6.2] [D-07] Solar pump station kit:
▪ 0 (No): NOT installed
▪ 1 (Yes): Installed
[A.2.2.6.3] [C-09] Alarm output on optional EKRP1HB
PCB:
▪ 0 (Normally open): The alarm output
will be powered when an alarm
occurs.
▪ 1 (Normally closed): The alarm
output will NOT be powered when an
alarm occurs. This installer setting
allows distinction between detection
of an alarm and detection of a power
failure to the unit.
See also table below (Alarm output
logic).
[A.2.2.6.4] [F-04] Bottom plate heater
▪ 0 (No): NOT installed
▪ 1 (Yes): Installed
Alarm output logic
[C-09] Alarm No alarm No power
supply to unit
0 (default) Closed output Open output Open output
1 Open output Closed output
Demand PCB
# Code Description
[A.2.2.7] [D-04] Demand PCB
Only applicable for EHBH/X04+08 and
EHVH/X04+08. Indicates if the optional
demand PCB is installed.
▪ 0 (No): NOT installed
▪ 1 (Yes): Installed
Energy metering
# Code Description
[A.2.2.8] [D-08] Optional external kWh meter 1:
▪ 0 (No): NOT installed
▪ 1: Installed (0.1 pulse/kWh)
▪ 2: Installed (1 pulse/kWh)
▪ 3: Installed (10 pulse/kWh)
▪ 4: Installed (100 pulse/kWh)
▪ 5: Installed (1000 pulse/kWh)
[A.2.2.9] [D-09] Optional external kWh meter 2:
▪ 0 (No): NOT installed
▪ 1: Installed (0.1 pulse/kWh)
▪ 2: Installed (1 pulse/kWh)
▪ 3: Installed (10 pulse/kWh)
▪ 4: Installed (100 pulse/kWh)
▪ 5: Installed (1000 pulse/kWh)
4.2.4 Quick wizard: Capacities (energy
metering)
# Code Description
[A.2.3.1] [6-02] Booster heater capacity [kW]
[A.2.3.6] [6-07] Bottom plate heater capacity [W]
4.2.5 Space heating/cooling control
Leaving water temperature: Main zone
# Code Description
[A.3.1.1.1] N/A Set point mode:
▪ 0 (Absolute): Absolute
▪ 1 (Weather dep.):
Weather
‑
dependent
▪ 2 (Abs + scheduled): Absolute +
scheduled (only for leaving water
temperature control)
▪ 3 (WD + scheduled):
Weather
‑
dependent + scheduled
(only for leaving water temperature
control)
[A.3.1.1.3] [1-00]
[1-01]
[1-02]
[1-03]
Weather
‑
dependent curve (heating):
[1-03]
[1-02]
Ta
Tt
[1-00] [1-01]
▪ T
t
: Target leaving water temperature
(main)
▪ T
a
: Outdoor temperature
[A.3.1.1.4] [1-06]
[1-07]
[1
‑
08]
[1-09]
Weather
‑
dependent curve (cooling):
[1-09]
[1-08]
Ta
Tt
[1-06] [1-07]
▪ T
t
: Target leaving water temperature
(main)
▪ T
a
: Outdoor temperature
Leaving water temperature: Additional zone
# Code Description
[A.3.1.2.1] N/A Set point mode:
▪ 0 (Absolute): Absolute
▪ 1 (Weather dep.):
Weather
‑
dependent
▪ 2 (Abs + scheduled): Absolute +
scheduled (only for leaving water
temperature control)
▪ 3 (WD + scheduled):
Weather
‑
dependent + scheduled
(only for leaving water temperature
control)