Daikin EBLA04E V Series Скачать руководство пользователя страница 76

Страница: 76 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

3.3.85 U8-06 – Bizone kit CANOpen communication error

Trigger

Effect

Reset

Communication
abnormality between user
interface PCB and bizone
kit box.

Unit will stop operating.

Automatic reset.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Perform a check of the user interface (main PCB). See

Possible cause:

Faulty user interface (main PCB).

Perform a check of the bizone kit PCB. See documentation of the bizone kit.

Possible cause:

Faulty bizone kit PCB.

Check the communication wiring between the unit and the bizone kit box. See

"5.1 Electrical circuit"

[

254].

Possible cause:

Faulty wiring between the unit and the bizone kit box.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.86 U8-07 – P1/P2 communication error

Trigger

Effect

Reset

Lost communication
between unit user
interface and unit.

Unit will NOT stop
operating.

Automatic reset.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Check the communication wiring between the user interface and the unit PCB.
See

"4.20 User interface"

[

234].

Possible cause:

Faulty wiring between the user interface and the unit PCB.

Check if the unit user interface functions correctly. See

Possible cause:

Faulty user interface on unit.

Perform a check of the hydro PCB. See

"4.12 Hydro PCB"

[

175].

Possible cause:

Faulty hydro PCB.

Check if the power supply is compliant with the regulations. See

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 76 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: