Daikin EBLA04E V Series Скачать руководство пользователя страница 73

Страница: 73 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

3.3.80 U7-00 – Outdoor unit: Transmission malfunction between main microcomputer - inverter

microcomputer

Trigger

Effect

Reset

Communication
abnormality between
main and inverter
microcomputer.

Unit will stop operating.

Manual reset via user
interface.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Perform a check of the main PCB. See

"4.14 Main PCB"

[

184].

Possible cause:

Faulty main PCB.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.81 U8-02 – Connection with room thermostat lost

Trigger

Effect

Reset

Communication
abnormality between unit
and room thermostat
after connection was
already made.

Unit will NOT stop
operating.

Automatic reset.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Check if the power supply is compliant with the regulations. See

Possible cause:

▪

Faulty or disturbance of the power supply (power supply MUST be within
range of nominal operating voltage ±4%),

▪

Power drop,

▪

Short circuit.

Check the communication wiring between the remote controller and the unit.
See

"4.20 User interface"

[

234].

Possible cause:

Faulty wiring between the remote controller and the unit.

Perform a check of the room thermistor:

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 73 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: