Daikin EBLA04E V Series Скачать руководство пользователя страница 219

Страница: 219 / 324

Components

Service manual

219

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Thermistor – Table B

T °C

kΩ

T °C

kΩ

T °C

kΩ

T °C

kΩ

806.5

618.9

478.8

373.1

292.9

231.4

184.1

147.4

118.7

96.13

78.29

64.1

52.76

43.63

36.26

30.27

100

105

110

115

25.38

21.37

18.06

15.33

13.06

11.17

9.585

8.254

120

125

130

135

140

145

150

7.131

6.181

5.374

4.686

4.098

3.594

3.161

Disconnect the thermistor connector from the appropriate PCB.

Measure the resistance between the appropriate pins of the thermistor
connector.

Check that the measured resistance value matches the resistance determined
through the measured temperature (earlier step in the procedure).

▪

E.g. R1T thermistor:

▪

Measured temperature with contact thermometer: 23.1°C,

▪

Resistance value determined through temperature (using the thermistor
table A):
Resistance at 23°C: 21.85 kΩ,
Resistance at 24°C: 20.90 kΩ,

▪

Disconnect connector and measure resistance between S90 pin 1‑2:
Measured resistance: 21.80 kΩ,

▪

Measured resistance value is inside the range. R1T thermistor passes the
check.

INFORMATION

All thermistors have a resistance tolerance of 3%.

INFORMATION

In most cases, the user interface allows to monitor the thermistors.

If the measured resistance value matches the resistance determined through the
measured temperature, but the temperature for the corresponding thermistor is
NOT correct on the user interface display, replace the applicable PCB.

Does the measured resistance of the
thermistor match with the
temperature determined resistance?

Action

Yes

Thermistor is OK. Return to the
troubleshooting of the specific error
and continue with the next procedure.

Replace the specific thermistor, see

"Repair procedures"

[

219].

Repair procedures

To remove the thermistor

Prerequisite:

Stop the unit operation via the user interface.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 219 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: