Daikin EBLA04E V Series Скачать руководство пользователя страница 153

Страница: 153 / 324

Components

Service manual

153

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Wire terminal U

Wire terminal V

Wire terminal W

Set the Megger voltage to 500 V DC or 1000 V DC.

Measure the insulation resistance between the following terminals. The
measured insulation resistance MUST be >3 MΩ.

▪

U–ground,

▪

V–ground,

▪

W–ground.

Compressor insulation measurements
are correct?

Action

Yes

Compressor is OK. Return to
troubleshooting of the specific error
and continue with the next procedure.

Replace the compressor, see

"4.7.2 Repair procedures"

[

153].

4.7.2 Repair procedures

To remove the compressor

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

[

202].

Prerequisite:

Remove the compressor insulation.

Prerequisite:

Recuperate the refrigerant from the refrigerant circuit, see

"5.2.2 Repair procedures"

[

261].

If needed, remove any parts to create more space for the removal of the
compressor.

DANGER: RISK OF ELECTROCUTION

Confirm the rectifier voltage is below 10 V DC before proceeding, see

Remove the cover of the compressor wire terminals.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 153 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: