Daikin EBLA04E V Series Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 324

Daikin EBLA04E V Series Скачать руководство пользователя страница 113

4

|

Components

Service manual

113

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

INFORMATION

The flow through the 4-way valve is correct if the water temperature after the heat
exchanger rises/drops when operating in

Heating

/Defrost mode.

Is the flow correct?

Action

Yes

Skip the next step.

No

Perform the next step of this procedure.

3

Connect a manifold to one of the service ports of the refrigerant circuit and
check the pressure (suction, discharge). Compare with normal operation
conditions of the unit.

Refrigerant pressure correct?

Action

Yes

Replace the body of the 4‑way valve,
see

"4.2.2 Repair procedures"

No

Leaks may be found in the refrigerant
circuit. Perform a pressure test of the
refrigerant circuit, see

"5.2.1 Checking

4

If the electrical check and position check have been performed with the unit
operating in:

▪

Defrost mode: Wait for the unit to switch to

Heating

(service monitoring

tool) mode and again perform the electrical check and position check.

▪

Heating

mode: There is a possibility to put the unit in Defrost operation via

Forced defrost

(see installer reference guide for more information).

Again perform the electrical check and position check when the unit is
operating in Defrost mode.

Is the flow correct?

Action

Yes

4‑way valve is OK. Return to the
troubleshooting of the specific error
and continue with the next procedure.

No

Replace the body of the 4‑way valve,
see

"4.2.2 Repair procedures"

4.2.2 Repair procedures

To remove the 4-way valve coil

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

Prerequisite:

If needed, remove any parts to create more space for the removal of

the 4‑way valve coil.

1

Remove the screw and remove the 4‑way valve coil from the 4‑way valve
body.

draft – 31/05/2022 15:53

«
...
111
112
113
114
115
...
»

Содержание EBLA04E V Series





































































































































































































































































































































Отзывы:

Нет отзывов