Daikin DRG0361DL00001S Скачать руководство пользователя страница 67

Страница: 67 / 113

SERVICING

Testing Primary Limit Control

Refer to the specification section to determine the proper

limit cutout temperature for the model being serviced.

In all instances the limit control is wired in series with the

ignition control.

If the temperature within the furnace should exceed this

setting, the control will open, de-energizing the ignition

control which in turn will open the electrical circuit to the

gas valve.

The control will automatically reset when the temperature

within the combustion chamber is sufficiently lowered.

HIGH VOLTAGE!

Disconnect ALL power before servicing

or installing this unit. Multiple power

sources may be present. Failure to do so

may cause property damage, personal injury

or death.

1. Remove electrical power to unit. Some units may

have more than one source of power.

2. Remove the wires from the limit control terminals.

3. Using an ohmmeter, test for continuity across the two

terminals.

4. If limit test open allow unit to cool and retest.

5. If still open, replace the control.

S-301 Testing Auxiliary Limit

The auxiliary limit control is a preset nonadjustable control

mounted in the blower compartment area.

It is connected in series with the rollout switch wiring to

the gas valve. If its temperature should be exceeded, it will

open, interrupting the voltage to the gas valve causing it to

open.

An additional limit (primary limit) control is required for

safety control of high temperature within the furnace or

ductwork.

AUXILIARY LIMIT SWITCH

HIGH VOLTAGE!

Disconnect ALL power before servicing

or installing this unit. Multiple power

sources may be present. Failure to do so

may cause property damage, personal injury

or death.

1. Remove the wires from the auxiliary limit control

terminals.

2. Using an ohmmeter, test for continuity across the two

terminals. No reading indicates the control is open.

Push the red reset button, test again - if still open,

replace the control.

3. If limit tests open, allow unit to cool and retest.

4. If still open, replace the control.

Содержание DRG0361DL00001S


















































































































Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды

Daikin DRG0361DL00001S, Инструкция по эксплуатации

Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды