manualshive.com logo in svg

Daikin ARQ, Руководство по установке и обслуживанию

Daikin ARQ - продукт высокого качества, обеспечивающий комфорт в вашем доме. Установочное руководство и другие инструкции доступны для бесплатного скачивания на manualshive.com. Наслаждайтесь удобством и эффективностью этого продукта, следуя инструкциям из руководства по установке.

Поделиться
Скачать
background image

www.DaikinApplied.com 41 

IM 1083-3

Form: 573882Y

Group: 

Unit Ventilator

Type: 

Basic Unit Data

Date: 

July 2017

 

Warranty

Daikin Applied Unit Ventilator

Warranty Registration Form

Check, test & start procedure for Unit Ventilators

This form must be completely filled out and returned to, Daikin Warranty Department within ten days in order to comply with the terms of the Daikin 

Applied warranty. Forms should be returned to Daikin Applied Warranty Department, P.O. Box 920, Auburn, NY 13021-0920.

Sales Office: ___________________________________S.O.#:  _______________________ Date Started: _______________
Job Name: _____________________________________________G.O. # __________________________________________
Job Location: ___________________________________________________________________________________________
Unit Location: _____________________________  Unit Tagging: __________________________________________________
Model No: _________________________________  Serial No.: __________________________________________________
Supply Voltage: L1/L2 __________  L2/L3 ____________  L3/L1 ______________  Rated: _____________________________
Room Fan Motor Amps: T1: ___________  RPM _________   

Nameplate Rating: ___________________________

  I .  Initial check

    A. Does electrical service correspond to unit nameplate? ................................................................................. Yes 

 No 

    B. Are all electrical power connections tight?  ................................................................................................... Yes 

 No 

    C. Does all field wiring conform to unit electrical schematic?  ........................................................................... Yes 

 No 

    D. Is unit installed per IM bulletin?  .................................................................................................................... Yes 

 No 

    F.  Cabinet paint O.K.?  ...................................................................................................................................... Yes 

 No 

    G. Cabinet bent?  ............................................................................................................................................... Yes 

 No 

    H. Do outdoor and indoor fans turn freely?  ....................................................................................................... Yes 

 No 

    I.  Are all setscrews on outdoor and indoor fan couplings tight?  ...................................................................... Yes 

 No 

    J.  Are end bearing bolts on outdoor and indoor fan shaft tight?  ....................................................................... Yes 

 No 

    K. Have the fan shaft end bearing and room fan motor been oiled (if applicable)?  .......................................... Yes 

 No 

    L.  Are outdoor air and return air dampers operating properly? ......................................................................... Yes 

 No 

    M. Is the filter clean?  ......................................................................................................................................... Yes 

 No 

    N. Is there excessive noise or vibration? .  ........................................................................................................ Yes 

 No 

      If Yes, corrective action (if any) ______________________________________________________________________________

 Il .  Controls check

    A. Does the unit have Daikin controls (MicroTech)? .......................................................................................... Yes 

 No 

      lf No, control company _____________________________________________________________________________________

      If controls are not by Daikin, skip to Section III.

    B. Condensate disposal system operating O.K. (drainIess AED)? .................................................................... Yes 

 No 

    C. Does unit start and perform per sequence of operation as stated in OM? .................................................... Yes 

 No 

    D. If the unit has a unit mounted sensor, has the insulation been 

      removed from the sampling chamber inlet? .................................................................................................. Yes 

 No 

  E. Are all sensors installed and insulated properly? .......................................................................................... Yes 

 No 

    F.  If the unit has MicroTech controls, room setpoint: _______°F Deadband 6° or _______°F 

 III .  Refrigeration system

    A. Has all field piping been leak tested to 100 psig (AVS, AVV, AVR, AHF, AHV & AHR) .................................. Yes 

 No 

    B. Is expansion valve bulb properly installed and insulated ............................................................................... Yes 

 No 

    C. High pressure control cutout (if applicable) _________ psig

    D. Crankcase heater operating O.K.? ................................................................................................................ Yes 

 No 

    E. Reversing valve operating O.K.?  .................................................................................................................. Yes 

 No 

    F.  Emergency heat operating O.K.?  ................................................................................................................. Yes 

 No 

    G. Piping correct (AVS, AVV, AVR, AHF, AHV & AHR to remote condensing unit)?  .......................................... Yes 

 No 

    H. Checked for refrigerant leaks?  ..................................................................................................................... Yes 

 No 

 IV . Hydronic piping check

    A. Is unit piping correct (the remainder of this section applies only to units with Daikin controls)? ................... Yes 

 No 

    B. Is the modulating control valve(s) piped correctly (valve controlled units)? .................................................. Yes 

 No 

    C. Is the modulating control valve(s) placed in the upright position (valve controlled units)? ............................ Yes 

 No 

    D. Is 2 - position control valve(s) piped correctly (face and bypass)? ................................................................ Yes 

 No 

Содержание ARQ













































Отзывы:

Нет отзывов

Похожие инструкции для ARQ

Lasko 3125 Operating Instructions preview
3125
Бренд: Lasko Страницы: 4
Fandis GF Series Mounting Instructions preview
GF Series
Бренд: Fandis Страницы: 2
WAFE 200 E User Manual preview
200 E
Бренд: WAFE Страницы: 18
Ultratec TWISTER X Operator'S Manual preview
TWISTER X
Бренд: Ultratec Страницы: 9
KORADO KORASMART TUBE 2400 Instruction Manual preview
KORASMART TUBE 2400
Бренд: KORADO Страницы: 96
Addvent AVX100WIDT Installation And Maintenance Instructions Manual preview
AVX100WIDT
Бренд: Addvent Страницы: 8
impress iM-783 Use And Care Book Manual preview
iM-783
Бренд: impress Страницы: 14
Toolway TOOLTECH 100082 User Manual preview
TOOLTECH 100082
Бренд: Toolway Страницы: 4
Qazqa Wind 91339 Instruction Manual preview
Wind 91339
Бренд: Qazqa Страницы: 26
Xpelair Premier CF40RSTD Installation And Maintenance Instructions Manual preview
Premier CF40RSTD
Бренд: Xpelair Страницы: 14
Zephir PF50CR Quick Start Manual preview
PF50CR
Бренд: Zephir Страницы: 16
NEO TOOLS 90-001 Instruction Manual preview
90-001
Бренд: NEO TOOLS Страницы: 24
Adler Europe 5903887804134 User Manual preview
5903887804134
Бренд: Adler Europe Страницы: 52
SummerAire SHRV2500DD Installation And Owners Operating Manual preview
SHRV2500DD
Бренд: SummerAire Страницы: 27
SummerAire SHRV115RD Product Specifications And Installation preview
SHRV115RD
Бренд: SummerAire Страницы: 32
Sealey SFF08 Instructions preview
SFF08
Бренд: Sealey Страницы: 2
Savoy House VILLAMOURNA Owner'S Manual preview
VILLAMOURNA
Бренд: Savoy House Страницы: 10
Dru Max Vent Installation Manual preview
Max Vent
Бренд: Dru Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды