background image

16

6.

   Minimum Deadband (1°F to 9°F) (1°C to 5°C)

Set the minimum separation between heat setpoint and cool setpoint in Auto Changeover Mode.
Press the 

 or 

 to set deadband value.

Press 

 to advance to the next screen.

CONFIG

5.

   Staged Off Outputs

Select whether the outputs for heating and cooling are staged off independently or are  

satisfied simultaneously.

     

 = Outputs off simultaneously.    = Outputs staged off independently.

 

Note: 

For 2 compressor heat pumps and multi-stage gas/oil systems, stage 3 is staged off

 

independently when SO is set to 

.

Press the 

 or 

 to set.

Press 

 to advance to the next screen.

CONFIG

7.

   Heat Source: There are six heat source settings:

WARNING!

Incorrect settings can damage system and/or cause potentially dangerous conditions. Use the code 

described in Configuration and Thermostat Lock.

CONFIG

 

Note: 

Daikin Water Source Heat Pumps require setting “9” for proper operation.

Water Source Heat Pump

8.

   Auxiliary Delay ON (0-60 minutes)

Set the delay time in minutes for auxiliary heat to be locked out after a call for second stage. This 

extra savings feature is used to temporarily lock out auxiliary heat devices, allowing just heat pump to 

try to satisfy heat call.
Press the 

 or 

 to select.

Press 

 to advance to the next screen.

CONFIG

HEAT

Содержание 910193131





































Отзывы: