Daihen OTC WB-M400 Скачать руководство пользователя страница 40

Страница: 40 / 141

ONNECTING

THE

ELDING

OWER

OURCE

ONNECTION

HAPTER

4-8

4.2.6

Connection of shielding gas

This section explains the procedure for connecting the the shielding gas. Refer also to the instruction
manual of wire feeder.

Attach the gas regulator to the gas cylinder.

Connect the gas hose to the gas regulator and the wire feeder.

●

For TIG welding, connect the gas hose to the welding torch for TIG welding.

Connection for shielding gas is complete.
In using the air-cooled welding torch, continue to perform the step described in "4.3

Grounding and

Connection of Input Power Supply".

• Be sure to observe the following points to prevent from suffocation due to gas leakage

or explosion.

– Be sure to turn off the shielding gas at the main tap when the welding power source

is not in use.

– Securely connect the gas hose and attach the gas regulator with a wrench so that

there is no gas leakage.

• For the gas regulator, make sure to use a device for compressed gas cylinder that

conforms to the specific application of the shielding gas.
Using an inappropriate gas regulator may cause explosion.

• Keep the cylinder upright and securely chained to a stationary support or a rack.

Falling or tipping of cylinder may cause serious injury.

• After five seconds have passed, the voltage is automatically provided.

Gas supply inlet

Gas regulator

Gas cylinder

Wire feeder

Gas cylinder

Gas hose

Содержание OTC WB-M400














































































































































Результаты поиска

Содержание OTC WB-M400

Отзывы:

Daihen OTC WB-M400, Руководство пользователя, Страница: 40 / 141

Результаты поиска

Содержание OTC WB-M400

Отзывы: