Dahua VTO4202F Series Скачать руководство пользователя страница 4

Страница: 4 / 36

Important Safeguards and Warnings III

Important Safeguards and Warnings

The following description is the correct application method of the device. Read the manual

carefully before use, in order to prevent danger and property loss. Strictly conform to the

manual during application and keep it properly after reading.

Operating Requirement



Do not place and install the device in an area exposed to direct sunlight or near heat

generating device.



Do not install the device in a humid, dusty or fuliginous area.



Keep its horizontal installation, or install it at stable places, and prevent it from falling.



Do not drip or splash liquids onto the device; do not put on the device anything filled with

liquids, in order to prevent liquids from flowing into the device.



Install the device at well-ventilated places; do not block its ventilation opening.



Use the device only within rated input and output range.



Do not dismantle the device arbitrarily.



Transport, use and store the device within allowed humidity and temperature range.

Power Requirement



The product shall use electric wires (power wires) recommended by this area, which shall

be used within its rated specification.



Use power supply that meets SELV (safety extra low voltage) requirements, and supply

power with rated voltage that conforms to Limited Power Source in IEC60950-1. For

specific power supply requirements, refer to device labels.



Appliance coupler is a disconnecting device. During normal use, keep an angle that

facilitates operation.

Содержание VTO4202F Series





































Результаты поиска

Содержание VTO4202F Series

Отзывы:

Похожие инструкции для VTO4202F Series

Бренды по названию

Популярные бренды

Dahua VTO4202F Series, Быстрый старт

Результаты поиска

Содержание VTO4202F Series

Отзывы:

Похожие инструкции для VTO4202F Series

Бренды по названию

Популярные бренды