Dahua DH-SD6C225U-HNI страница 9 Скачать руководство пользователя

Страница: 9 / 29

IR INTELLIGENT SPEED DOME INSTALLATION

1.1

Installation Preparation

Basic Requirement



All installation and operation here should conform to your local electrical safety codes.



Before installation, please open the package and check all the components are included.

Please make sure the speed dome installation environment and installation mode can meet

your requirement. If there is special requirement, please contact your local retailer for more

information.



We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

Check installation space and installation location intension

Please make sure the installation environment has enough space to install the speed dome and

its corresponding bracket.

Please make sure the ceiling, wall and the bracket can support the speed dome and its

corresponding installation component. It shall sustain the 8X weight of the speed dome.

About cable

Please select the cable according to your transmission distance.

The minimum video coaxial-cable requirement is:



75 ohm.



Full cable with copper conductor



95% knitted copper shield

International Model

Max Transmission Distance
(Ft\M)

RG59/U

750Ft (229M)

RG6/U

1,000Ft (305M)

RG11/U

1,500Ft (457M)

Note:

The above can be applied to analog speed dome and network speed dome

International Model

Max Transmission Distance

(M\Ft)

SYV-75-3

720P(25fps\30fps)

：

500M/1640Ft

720P(50fps\60fps)

：

300M/984Ft

1080P(25fps\30fps): 300M/984Ft

Note:

The above can be applied to HDCVI speed dome.

Set dial switch button

Set dial switch button according to control protocol and speed dome address. (Please refer to

user

’s manual for detailed information.)

Please keep all package material well for future use

Содержание DH-SD6C225U-HNI






























Результаты поиска

Содержание DH-SD6C225U-HNI

Отзывы:

Похожие инструкции для DH-SD6C225U-HNI

Бренды по названию

Популярные бренды

Dahua DH-SD6C225U-HNI, Руководство по установке

Результаты поиска

Содержание DH-SD6C225U-HNI

Отзывы:

Похожие инструкции для DH-SD6C225U-HNI

Бренды по названию

Популярные бренды