background image

Quick Start Guide 

Table 1-2 Alarm information 

Port Name 

Description 

ALARM_OUT 

Outputs alarm signal to alarm devices. 

 

When connecting to alarm device, only the ALARM_OUT port and 

ALARM_OUT_GND port with the same number can be used 

together. 

ALARM_OUT_GND 

ALARM_IN 

Receives the switch quantity signal of external alarm sources. 

 

Connect different alarm input devices to the same 

ALARM_IN_GND port. 

ALARM_IN_GND 

1.2 Connecting Alarm Input/Output 

The camera can connect to external alarm input/output devices through the digital input/output 
port. 

 

Alarm input/output is available on select models. 
Step 1 

Connect the alarm input device to the alarm input end of the I/O port. See Figure 1-2. 
The device collects different statuses of the alarm input port while the input signal is idling 
and being grounded. 

  Device collects logic "1" when the input signal is connected to +3 V to +5 V or idling. 

  Device collects logic "0" when the input signal is grounded. 

Figure 1-2 Alarm input 

 

Step 2 

Connect the alarm output device to the alarm output end of the I/O port. The alarm output 
is an open-drain output, which works in the following modes. 

  Mode A: level application. The alarm outputs high and low level signals, and the alarm 

outlet is OD, which requires external pull-up resistance (10 K Ohm typical) to work. The 
maximum external pull-up level is 12 V, maximum port current is 300 mA, and the 
default output signal is high-level (external pull-up voltage). The default output signal 
switches to low- level when an alarm is triggered (As long as the operating current is 
below 300 mA, the output low-level voltage is lower than 0.8 V). 

  Mode B: switch application. Alarm output is used to drive the external circuit, the 

maximum voltage is 12 V and the maximum current is 300 mA. If the voltage is higher 

Содержание IPC-HDW5449H-ASE-D2-0280B



















Отзывы: