background image

 

 

ii 

3. Operation and Daily Maintenance  

 

Please do not touch the heat dissipation component of the device directly in order to avoid scald.  

 

Please do not dismantle the device; there is no component which can be fixed by users themselves 

in the machine. It may cause water leakage or bad image for the device due to unprofessional 

dismantling. Please contact after-sale service to replace desiccant if it becomes green. 

 

It is recommended to use the device with thunder proof device in order to improve thunder proof 

effect.  

 

The grounding holes of the product are recommended to be grounded to further enhance the 

reliability of the camera. 

 

Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust 

or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if 

it is necessary to clean.  

 

Always use the dry soft cloth to clean the device.  If there is too much dust, please use the water to 

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean 

the device. Don

’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with 

abrasiveness, otherwise it will damage the surface coating or reduce the working performance of 

the device. 

 

Dome  cover  is  an  optical  device,  please 

don’t  touch  or  wipe  cover  surface  directly  during 

installation and use, please refer to the following methods to deal with once dirt is found:  

 

Stained with dirt 

 

Use oil-free soft brush or hair dries to remove it gently.  

 

Stained with grease or fingerprint  

 

Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or 

paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change 

the cloth and wipe several times if it is not clean enough.  

 

Warning 

 

Please modify the default password after login in order to avoid being stolen. 

 

Please  use  the  standard  accessories  provided  by  manufacturer  and  make  sure  the  device  is 

installed and fixed by professional engineers.  

 

Please prevent the device surface from the radiation of laser beam when using laser beam device.  

 

Please  do  not  provide  two  or  more  power  supply  modes  for  the  device,  otherwise  it  may  cause 

damage to the device.  

 

Statement  

 

Please refer to the actual product for more details; the manual is just for reference.  

 

The manual will be regularly upgraded according to the product update; the upgraded content will 

be added in the manual without prior announcement.  

 

Please contact the supplier or customer service if there is any problem occurred when using the 

device. 

Содержание IPC-HDW5231R-Z


















Отзывы: