background image

17

(TROUBLE 1)  Oven does not operate at all ; any inputs can not be accepted.

TROUBLESHOOTING GUIDE 

Following the procedure below to check if the oven is defective or not.

1. Check grounding before trouble checking.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor.
4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts

and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter.

NOTE  : When electric parts are checked, be sure the power cord is not inserted the wall outlet.

Check wire harness, wiring and connected of the terminals and power cord before check the parts listed
below.

CONDITION

CHECK

Check continuity of interlock
monitor switch with door closed

Check continuity of of primary
interlock switch contact with door
partially open until interlock moni-
tor switch contact close

Malfunction of
interlock moni-
tor switch

Shorted con-
tacts of primary
interlock switch.

RESULT

Continuity

No Continuity

No Continuity

Replace fuse

CAUSE

REMEDY

Replace

Fuse blows.

Replace

Defective low
voltage trans-
former

0

or infinite

Approx.

150~310 

(normal)

Replace

Check continuity of primary
winding of low voltage trans-
former

Defective high
voltage capacitor

Normal

Replace

Disconnect one side of the lead
wire connected form high volt-
age transformer to the high volt-
age capacitor and operate the
unit

Continuity

Defective high
voltage trans-
former

Fuse again

blows

Replace

Содержание KOR-1A7G
































Отзывы: