Daewoo KOR-1A4H Скачать руководство пользователя страница 3

SAFETY AND PRECAUTIONS

CAUTION  : This Device is to be Serviced Only by Properly Qualified Service Personnel. Consult the Service

Manual for Proper Service Procedures to Assure Continued Safety Operation and for Precautions
to be Taken to Avoid Possible Exposure to Excessive Microwave Energy.

1. FOR SAFE OPERATION 

Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and
may cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a trained service personnel should make repairs.)
1)  A broken door hinge.
2)  A broken door viewing screen.
3)  A broken front panel, oven cavity.
4)  A loosened door lock.
5)  A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has
concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.

2. FOR SAFE SERVICE PROCEDURES

1) If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing

the oven.

2) If any certified oven unit is found to servicing, a microwave emission check should be performed prior to

servicing the oven.

(a) inform the manufacturer, importer or assembler,
(b) repair the unit at no cost to the owner,
(c) attempt to ascertain the cause of the excessive leakage,
(d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.

3) If the oven operates with the door open, the service person should tell the user not to operate the oven and

contact the manufacturer and CDRH immediately.

2

IMPORTANT :
The wire in this mains lead coloured in accordance with the following code.

Green-and-yellow : Earth
Blue

: Neutral

Brown

: Live

As the colours of the wires in the manins lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The  wire which is loloured green-and-yellow must be connected to the termianl in the plug which is marked
with the letter ‘E’, earth symbol or coloured green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked the letter ‘L’ or coloured red.

NOTE  :

This oven is designed for counter-top use only.

Содержание KOR-1A4H

































Отзывы: