manualshive.com logo in svg

Daewoo KOR-1A0A0A, Руководство по обслуживанию, Страница: 2 / 51

Поделиться
Скачать
Daewoo KOR-1A0A0A Скачать руководство пользователя страница 2

1

PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

(a) Do not operate or allow the oven to be operated with the door open.

(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3)
Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and
latches, (5) Evidence of dropping or abuse.

(c) Before turning on power to the microwave oven for any service test or inspection within the microwave

generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper
alignment, integrity, and connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave

generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.

(e) A microwave leakage check to verify compliance with the Federal performance standard should be

performed on each oven prior to release to the owner.

TABLE OF CONTENTS

1. SAFETY AND PRECAUTIONS....................................................................................................................................2

2. SPECIFICATIONS ........................................................................................................................................................3

3. EXTERNAL VIEW .........................................................................................................................................................6

3-1. OUTER DIMENSION ..........................................................................................................................................6

3-2. FEATURE DIAGRAM .........................................................................................................................................9

3-3. CONTROL PANEL............................................................................................................................................11

4. INSTALLATION ..........................................................................................................................................................15

5. CONTROL PANEL .....................................................................................................................................................16

6. DISASSEMBLY AND ASSEMBLY ............................................................................................................................17

7. INTERLOCK MECHANISM AND ADJUSTMENT.....................................................................................................27

8. TROUBLESHOOTING GUIDE ...................................................................................................................................28

9. MESUREMENT AND TEST .......................................................................................................................................32

9-1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................32

9-2. MICROWAVE RADIATION TEST ....................................................................................................................33

9-3. COMPONENT TEST PROCEDURE................................................................................................................34

10. WIRING DIAGRAM...................................................................................................................................................35

11. PRINTED CIRCUIT BOARD ....................................................................................................................................37

12. EXPLODED VIEW AND PARTS LIST    ..................................................................................................................47

11-1. DOOR ASSEMBLY.........................................................................................................................................47

11-2. CONTROL PANEL ASSEMBLY.....................................................................................................................47

11-3. TOTAL ASSEMBLY........................................................................................................................................47

Содержание KOR-1A0A0A




















































Отзывы:

Нет отзывов