Daewoo KOG-86AR7S Скачать руководство пользователя страница 19

17

(TROUBLE 1)  Oven does not operate at all ; any inputs can not be accepted.

TROUBLESHOOTING GUIDE 

Condition

Check

Result

Cause

Remedy

Fuse blows

Check continuity of inter-
lock monitor switch 
with door closed
(COM           NC)

Check continuity of pri-
mary interlock switch con-
tact with door partially
open until interlock moni-
tor switch contact close

Check continuity of 
primary winding of low
voltage transformer

Disconnect high voltage
fuse and operate the unit

Continuity

Continuity

Continuity

No

Continuity

or

infinite

Fuse again
blows

Approx.

150~310

(normal)

Replace

Replace

Replace

NOTE

NOTE

Malfunction of 
interlock
monitor switch

No

Continuity

Check continuity of pri-
mary interlock switch con-
tact with door partially
open until interlock moni-
tor switch contact close
(COM

NO)

Replace

NOTE

Shorted contacts of
primary interlock
switch.

Shorted contacts 
of primary interlock
switch

Defective low volt-
age transformer

Defective high
voltage transformer

Replace

Following the procedure below to check if the oven is defective or not.

1. Check grounding before trouble checking.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor.
4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts

and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter.

NOTE  : When electric parts are checked, be sure the power cord is not inserted the wall outlet.

Check wire harness, wiring and connected of the terminals and power cord before check the parts listed
below.

18

Содержание KOG-86AR7S



































Отзывы: