manualshive.com logo in svg

Daewoo KOG-3Q47, Руководство по обслуживанию, Страница: 5 / 25

Поделиться
Скачать
Daewoo KOG-3Q47 Скачать руководство пользователя страница 5

EXTERNAL VIEW

1. OUTER DIMENSION

2. FEATURE DIAGRAM

465

279

384

4

1

Door seal - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage.

2

Cover Heater

3

Heating Element

4

Oven cavity

5

Safety interlock system

6

Knob V.P.C - Used to select a microwave power level.

7

Knob timer - Used in setting cooking time for all functions.

8

Metal Rack

9

Coupler - This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.

0

Roller guide - This must always be used for cooking together with the glass cooking tray. 

q

Glass cooking tray - Made of special heat resistant glass. Food in a proper receptacle is placed on this tray for cooking.

w

Door viewing screen - Allows viewing of food. The screen is designed so that light can pass through, but not the

microwave.

e

Door hook - When the door is closed, it will automatically shut off. If the door is opened while the oven is operating, the

magnetron will immediately stop operating.

Содержание KOG-3Q47


























Отзывы:

Нет отзывов