manualshive.com logo in svg

Daewoo KOC-910K0P(AL), Руководство по обслуживанию, Страница: 16 / 40

Поделиться
Скачать
Daewoo KOC-910K0P(AL) Скачать руководство пользователя страница 16

15

1) Remove a screw

①

and pull out Cover motor B

②

.

2) Remove a screw

③

and pull out cover B

④

.

3) Pull out the Harness convection-B

⑤

.

4) Remove four screws

⑮

and then pull out the Rear heater assembly.

5) Remove a Nut

⑪

and the pull out the Fan convection

⑩

and Washer plain

⑨

.

6) Remove three screws

⑧

and then separate the Cover heater B

⑦

and the Insulator heater B

⑭

7) Pull out two Heaters

⑥

from the Cover Heater B

⑦

8) Remove two screws

⑬

and then separate the Insulator heater B

⑭

and Motor shaded pole

⒃

.

9) Remove the C-Ring

⒕

and then pull out the Fan

⒔

from Motor shaft.

10) Reverse the above steps for reassembly.

3

4

5

6

7

8

9

10

11

12

14

13

15

16

17

18

2

1

REF NO.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

PART CODE

7112401011

3511407300

7112401011

3511407900

3512766900

3512804700

3511407700

7113400814

7400504211

3511800700

7391400065

3512766800

7051400811

3513302900

7113400814

3963330100

3511800800

7402704600

PART NAME

SCREW TAPPING

COVER MOTOR B

SCREW TAPPING

COVER B

HARNESS CONVECTION-B

HEATER MIRACLON

COVER HEATER B

SCREW TAPPING

WASHER PLAIN

FAN CONVECTION

NUT HEX

HARINESS CONVECTION-A

SCREW MACHINE

INSULATOR HEATER B

SCREW TAPPING

MOTOR SHADED POLE

FAN

C-RING

DESCRIPTION

T1 TRS 4

×

10 MFZN

SA1D-80 T0.5

T1 TRS 4

×

10 MFZN

SA1D-80 T0.5

KOC-1B0K0S

110V 550W

SA1D-80 T0.5

T1 BIN 4

×

8 MFNI

PW5-5 BRASS

SA1D-80 T0.5

6N-1.4BSNI

KOC-1B0K0S

PAN 4

×

8 SW MFZN

SBHG-1 T0.5

T1 BIN 4

×

8 MFNI

MW10GA-T01

PP GF20

CR-5 SK5

Q’TY

1

1

2

1

1

2

1

3

1

1

1

1

2

1

4

1

1

1

REMARK

12. To remove Rear heater assembly parts.

Содержание KOC-910K0P(AL)









































Отзывы:

Нет отзывов