manualshive.com logo in svg

Daewoo DTK-28 Series, Руководство по обслуживанию, Страница: 59 / 71

Поделиться
Скачать
Daewoo DTK-28 Series Скачать руководство пользователя страница 59

CP-850/F Service Manual

-58-

Mute : In this mode the amplifier is DC biased but not operational (no audio output). This allows the input coupling
capacitors to be charged to avoid pop-noise. The devices is in mute mode when 2.5 V < VMODE < (Vcc-1.5 V).

Operating : In this mode the amplifier is operating normally. The operating mode is activated at VMODE < 0.5 V.

5.8 VERTICAL DEFLECTION
The vertical driver circuit is a bridge configuration. The deflection coil is connected between the output amplifiers, which
are driven in phase opposition. The differential input circuit is voltage driven. The input circuit is especially intended for
direct connection to driver circuits which deliver symmetrical current signals, but is also suitable for asymmetrical
currents. The output current of these devices is converted to voltages at the input pins via resistors R350 and R351.
The differential input voltage is compared with the output current through the deflection coils measured as voltage
across R302, which provides internal feedback information. The voltage across R302 is proportional to the output
current.

5.8.1

FLYBACK VOLTAGE

The flyback voltage is determined by an additional supply voltage Vflb. The principle of operation with two supply
voltages (class G) makes it possible to fix the supply voltage Vp optimum for the scan voltage and the second supply
voltage Vflb optimum for the flyback voltage. Using this method, very high efficiency is achieved. The supply voltage
Vflb is almost totally available as flyback voltage across the coil, this being possible due to the absence of a coupling
capacitor.

5.8.2

PROTECTION

The output circuit has protection circuits for :

- Too high die temperature
- overvoltage of output stage A

5.8.3

GUARD CIRCUIT

The guard signal is not used by the video IC to blank the screen in case of fault condition.

5.8.4

DAMPING RESISTOR 

For HF loop stability a damping resistor (R331) is connected across the deflection coil.

5.8.5

EAST-WEST AMPLIFIER (TDA8358J ONLY)

The East-West amplifier is current driven. It can only sink currents of the diode modulator circuit. 
A feedback resistor R397 is connected between the input and output of this inverting amplifier in order to convert the
East-West correction input into an output voltage.

Содержание DTK-28 Series








































































Отзывы:

Нет отзывов