EN
7
5. TECHNICAL INFORMATION
Power:
1400 W
No load speed:
800 rpm
Mixing paddle diameter:
115 mm
Mixing rod length:
580 mm
Safe level:
II
Includes:
Mixing rod 1 pc.
Carbon brush 1 pair.
Auxiliary handle 1 pc.
6. EXPLODED VIEW
4. MAITENANCE
CAUTION
• Always be sure that the tool is switched off and unplugged before attempting to perform inspec-
tion or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
Replace carbon brush
1.Limit mark
Remove and check the carbon brushes regularly.Replace when they wear down to the limit mark.
Keep the carbon brushes clean and free to slip in the holders.Both carbon brushes should be repla-
ced at the same time. Use only identical carbon brushes.Use a screwdriver to remove the brush
holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.
1. Brush holder cap.
2. Screwdriver.
Installing the back handle
1. Handle components.
2. Screw.
Install the two handle components and screw them firmly.
3. OPERATION
Mixing
CAUTION
Do not use for mixing combustible materials, such as for dilution
。
It is a solvent paint, otherwise it
may cause personal injury harm.
If the mixing blade is exposed during mixing, the material will splash.
1. During operation, be sure to hold the top or back handle, auxiliary handle and switch handle tightly.
2. Put the mixing blade into the material completely and start the tool after confirming the safety of
the working environment.
3. When mixing, move the mixing blades up and down to fully mix all materials.
4. After the completion of mixing, turn off the machine, make sure that the mixing blade stops rota-
ting completely, and then remove it from the vessel.
Power tool use and precautions
1. Do not abuse the power tool. Use the appropriate power tool according to the application. Selec-
ting the power tool with the appropriate design rating will make your work more effective and safer
2. If the switch cannot turn the tool power on or off, the power tool cannot be used. The power tool
that cannot be controlled by the switch is dangerous and must be repaired.
3. Before making any adjustments, you must unplug the power supply from the power supply or
disconnect the battery case before replacing the accessories or storing the power tool. This protec-
tive measure will reduce the risk of sudden start of the power tool.
4. Keep idle power tools out of the reach of children and don't let power tools that are unfamiliar with
or uninformed about these instructions. Power tools are dangerous in the hands of untrained users.
5. Maintenance of power tools Check for installation deviations or jamming of moving parts.
Damage to parts and other conditions that affect the operation of power tools. Damaged. Power
tools must be repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Well- maintained tools with sharp cutting edges are not easy
to get stuck and easy to control.
According to the instruction manual and the special type requirements of the power tool to be used,
the working conditions and work performed are used to use the power tool. The attachment of the
tool and the tool, etc. Using the power tool as an operation that does not meet the requirements
may result in a dangerous situation.
Service
1. Send your power tool to a professional service person. You must use the same spare parts for
replacement. This will ensure the safety of the power tool being repaired.
2. Follow the instructions in this manual when lubricating oil and replacing accessories.
3. The handle must be kept dry and clean.
Special safety rules
Do not use it for convenience or because you are familiar with the operation of this product After
repeated use, do not strictly follow the safety rules. Unsafe or incorrect use of the power tool may
cause serious personal injury.
1. When the cutting tool may touch the hidden line or its own wire, the insulating handle of the tool
should be held. Contact with the live wire will electrify the exposed metal parts of the tool, causing
the operator to get an electric shock.
2. Make sure that there is no one underneath when working at a high position.
3. The tool should be tightly gripped.
4. The hand must be away from the rotating parts.
5. Do not allow the tool to run when no one is operating only when holding the tool.
6. Do not touch the drill bit or the workpiece immediately after the end of the operation because
they may be extremely hot and can burn the skin.
7. Use the auxiliary handle provided with the tool. Handling the malfunction can cause personal injury.
8. Wear earmuffs when using impact drills. Exposure to noise can cause hearing damage.
WARNING
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
2. FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the tool is switched off and unplugged before adjusting or checking function on
the tool.
SWITCH ACTION CAUTION:
Before plugging in the tool, always check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
During the operation, the switch can be locked in the “ON” position to make the operation more
comfortable
Please be careful when setting at “ON” position
Hold the tool firmly
1.Lock button
2.Switch
When starting the tool, just pull the switch trigger. Release the switch trigger to stop.
During continuous operation, please pull the switch trigger and press the lock button,then release
the switch trigger.
To stop the tool from the locked position, pull the switch go to the bottom and let go
ASSEMBLY CAUTION:
Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing the connect shaft
1. Hex nut
2.Axle
3.Axle tube
Screw the shaft into the shaft tube until the hexagon nut contacts the shaft tube
1. Wrench
2. Axle tube
3. Wrench
Fix the axle tube with one wrench and tighten the hexagon nut with the other wrench in the direction
of the arrow.
Installing the top handle (auxiliary handle)
Screw the top grip on the tool securely.
The tool is used for mixing wall materials and other materials (Except combustible)
Power supply
This tool can only be connected to the same voltage as the voltage shown on the nameplate
1. GENERAL SAFETY RULES
WARNING:
Read and understand all instructions.Failure to follow all instructions listed below ,may result in
eletric shock ,fire and / or serious personal injury.
Workplace
Keep the workplace clean and bright.
Confusion and darkness can cause accidents.
1. Do not operate the power tool in an explosive environment such as a flammable liquid gas or
dust. A spark generated by a power tool will ignite dust or gas.
2. Allowing children and bystanders to leave and manipulating power tools Distraction will make you
relax control.
Electrical Safety
1. The power tool plug must be matched with the socket. The plug must not be modified in any way.
The power tool to be grounded cannot use any conversion plug. The unmodified plug and the mat-
ching socket will reduce the risk of electric shock.
2. Avoid human contact with grounded surfaces such as pipes, heat sinks and refrigerators. If your
body is grounded, it will increase the risk of electric shock.
3. Do not expose power tools to rain or moisture. Water entering power tools increases the risk of
electric shock
4. Do not abuse the wire. Never use wire to carry the power tool or pull out its plug. Keep the power
tool away from hot oil. Sharp edges or moving parts. Damaged or entangled wires can increase the
risk of electric shock.
Personal safety
1. Be vigilant When operating the power tool, pay attention to the operation and keep it awake. Do
not operate the power tool under fatigue. Alcohol or treatment reaction. Distraction during operation
of the power tool can cause serious personal injury.
2. Use safety devices Always wear goggles Safety devices such as dust masks under appropriate
conditions Non-slip safety shoes Safety helmets Hearing protection devices can reduce personal injury.
3. Avoid sudden start. Make sure the switch is in the off position when the plug is inserted. Inserting
the plug on the switch that is connected to the power supply or when the switch is on may cause
danger.Remove all adjustment keys or wrenches before the power tool is turned on. The wrench or
key left on the rotating parts of the power tool can cause personal injury.
4. Do not stretch your hands too long. Always pay attention to the balance between the feet and the
body so that you can control the power tools well under unexpected conditions.
5. Dress properly Do not wear loose clothes or wear jewelry Let your hair Clothes and sleeves away
from moving parts Loose clothes Adhesives or long hair may get caught in moving parts.
6. If equipment is provided for connection to the dust collector of the chip evacuator, make sure
they are connected and used properly.
Use these devices to reduce the risk of debris
