3
Attaching Top Lid
Place the handle towards the rear side of the Air pot. Insert the shaft of the
hinge on the lid into the hinge holder. Ensure that lid attached properly. Close
and press on lid until it clicks.
3
Using The Air pot For The First Time
1. Wash and rinse inner tank with water.
2. Fill water up to “Full” water indicator scale.
3. Boil once and discard water by pumping it out.
OPENING TOP LID
Set Air pot on table top. Open top lid
and fill water to
desired capacity.
3
Always fill water above the
minimum mark but below the
maximum water level line
indicator.
CLOSING TOP LID
Carefully close lid by pressing down
until a click sound is heard.
3
Do not close the upper lid
forcefully (Hot water may gush
out and cause scalding).
1.
Insert the receptacle into the Air
pot power inlet. Plug in the other
end of the power cord plug into
the wall socket.
2.
Do not switch on when the
container is empty.
3
When rotating the body, be
careful that the power cord does
not get in the way.
BOIL KEEP WARM
BOIL BOIL
KEEP KEEP
WARM WARM
1.
“Boil” light is on during boiling
process.
2.
It will switch to “keep warm”
automatically after the water is
boiled.
3
Do not open the upper lid.
3
Do not touch the steam coming
out of the steam vent.
3
Do not place cloth or any other
items covering the steam vent.
3
Do not dispense hot water while
the water is boiling.
POURING HOT WATER
1.
The hot water might not
dispense smoothly right after
boiling.
2.
Press on the “AUTO
DISPENSE” button to dispense
hot water.
3
CAUTION: Always keep the lid
closed while the Air Pot is in
operation as there is hot steam
trapped under the lid.
3
Do not press the dispensing
button when the inner water tank
is empty.(Doing so can cause
damage.)
3
You cannot dispense hot water
by pressing Auto Dispense
button, Cup Switch or the
Manual Dispenser if the Air Pot
is unplugged.
REFILL WATER
When water reaches to minimum
water level mark, add water for
automatic boiling.
3
Do not add water above full-
water indicator scale. Water
level should not be below the
minimum mark as it may cause
malfunctions.
- 3-
Cleaning And Maintenance
1.
Always allow appliance to cool before cleaning.
2.
Remember to unplug power cord from wall socket and power inlet.
3.
Detach upper lid and pour out remaining water.
4.
If mineral deposits accumulate, loud noises may be heard during boiling and
you may face difficulties dispensing hot water. Regular cleaning will avoid
such problems.
Wipe upper lid and body with a soft,
clean, damp cloth.
3
Never immerse any part of the
Air Pot in water.
3
Never splash water on the
operation panel.
3
Do not use abrasive materials to
clean appliance.
-4-
RE-BOIL THE HOT WATER
UNDER THE KEEP WARM MODE.
3
Re-boiling a full tank of water
takes about 3 minutes.
3
Before Re-boiling, make sure
the water level is above the
minimum mark.
3
The Re-boil button may have
no effect right after the water
has boiled.
3
When adding water to the Air
pot, be careful not to get scald
by hot steam as you open the
top lid.
3
Once the Re-boil button is
pressed, the boiling process
cannot be reset until the Air
Pot automatically switches to
the keep warm mode.
3
Do not press the Re-boil
button repeatedly as the
continuous boiling process will
cause malfunction.
AFTER USE
Unplug the power cord
Detach the lid and
Dispose the water.
3
Allow the Air Pot to dry
completely.
3
Do not place the Air pot in a
dishwasher or dish dryer. This
will damage the Air pot.
3
If not in use, seal the unit in a
plastic bag to protect it from
dust and insects.