Daekyung Black Bear DH Series Скачать руководство пользователя страница 15

Страница: 15 / 18

Black Bear is a registered trademark of Daekyung Co., Ltd.
1521-6 Dadae-dong, Saha-gu, Busan, Korea Tel: +82)51-264-6611 Fax: +82)51-264-6615

BLACK BEAR HOIST

- 15 -

7.2.3 Annual Inspection

1) Disassemble the gear box and check for abrasion/damage of gear parts. Replace them if necessary.

2) Check for abrasion/damage of ratchet, stopper (pawl), or brake lining. Replace them if necessary.

3) When the inspection is completed, assemble the hoist and fill the lubricating grease.

4) Check for any unusual noise, etc. by hoisting/descending the hoist about 40-50cm for 2-3 times

without any load suspended. Then try the same inspection again with a load suspended, and check for
any sliding and other problems. Use the hoist if everything is working properly.

7.3 Check List

Part

Check List

Check Standard

Body

Exterior Appearance

There should not be any rust, dent, or damage.

Noise

There should not be any unusual or excessive noise.

Side Plate

There should not be any dent, abrasion or deformation.

Reduction Gear

There should not be any dent, abrasion or deformation.

Load Sheave

There should not be any dent, abrasion or deformation.

Load Chain

Rust/Dent

There should not be any rust, dent, or deformation.

Oil Lubrication

Oil must be thoroughly and evenly distributed.

Top & Bottom Hook

Deformation

Hooks should not be deformed (sagging or cracked open).

Holder

There should not be any dent, abrasion or deformation.

Bottom Hook Pin

There should not be any abrasion or bending.

Safety Latch

Safety Latch must be in place and it should move freely.

Other

Hand Chain

Hand chain must operate smoothly.

Содержание Black Bear DH Series



















Результаты поиска

Содержание Black Bear DH Series

Отзывы:

Похожие инструкции для Black Bear DH Series

Бренды по названию

Популярные бренды

Daekyung Black Bear DH Series, Руководство пользователя

Результаты поиска

Содержание Black Bear DH Series

Отзывы:

Похожие инструкции для Black Bear DH Series

Бренды по названию

Популярные бренды