background image

 Section 1 - Important Safety Instructions 

  

Page 

 Section 1

 

- Important Safety Instructions 

 

 

Operate this appliance only as specified in this manual or the use and care manual. 

 

Only a qualified installer should install this appliance. 

 

Other than performing procedures specified in the Wall Oven Use and Care Manual, only a qualified service 

technician should service this appliance. To obtain the name of your closest Dacor service representative, call 

(800) 793-0093. A list of service representatives is also available at 

www.dacor.com

 

Before attempting to service or connect this appliance to electrical power, turn off the electrical power supply. 

Failure to disconnect the power supply during installation or service may result in electrical shock or fire hazard. 

 

This appliance must be properly grounded whenever electrical power is applied. 

 

This appliance must be connected to a grounded, metallic, permanent wiring system. The grounding connectors 

must be connected to the grounding terminal or lead on the appliance. Failure to do so may result in an 

electrical shock hazard. 

 

Do not ground this appliance to a gas supply pipe or hot water pipe. 

 

A ground connection to a cold water pipe must have a metal continuity to electrical ground and must not be 
interrupted by insulating materials. Any insulating materials must be jumped as shown in the installation 

instructions. 

 

Use only connectors specially designed and certified for joining copper and aluminum to splice the appliance 

copper wire to the aluminum house wiring. 

 

Do not install a fuse in the neutral or ground circuit during installation. A fuse in the neutral or ground circuit 
may result in an electrical shock hazard. 

 

Do not install this appliance if the electrical service provided does not meet the product specifications on the 

model and serial number plate (see page 3). The electrical service must be installed or changed only by a 

licensed electrician. 

 

Do not operate this appliance if it has a damaged electrical cord. 

 

Failure to install the mounting screws may result in movement or tipping of the oven during use and may result 
in personal injury. 

 

Use an appliance dolly to move the appliance or when installing it or removing it from the wall for service. Use 

of an appliance dolly will minimize the risk of personal injury as a result of the oven tipping. 

 

Use the oven only for cooking tasks expected of a home appliance as outlined in this manual. Do not use 

corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat food. It is not 

designed for industrial or laboratory use. 

 

Do not touch the interior surfaces of the oven during or immediately after use. Do not allow clothing or other 

flammable materials to contact interior surfaces of the oven until they have had sufficient time to cool. 

 

Exercise caution when opening the oven door. Let hot air or steam escape before looking or reaching into the 

oven. 

 

Do not store combustible, flammable, or explosive materials in the oven or in adjacent cabinets. 

 

Do not attempt to disengage the oven door’s hinge locks with the door removed from the oven. The hinge 
springs could release and cause personal injury. 

 

Do not lift or carry the oven door by the door handle. 

 

  

WARNING:

 

www.Appliantology.org

Содержание MORS136

























Отзывы: