background image

6

Installation Instructions

Verify the Package Contents

Cut the shipping carton open and use it as a pad 

• 

beneath the dishwasher until the legs are installed. 

With the assistance of at least one person, place the 

unit to the side of the cabinet opening.
Remove all of the packing materials from inside and 

• 

outside of the unit. 

DO NOt

 allow any of the shipping 

materials, loose screws or plastic to remain inside. 
Unpack the parts box and verify that all of the parts 

• 

listed have been provided. If any item is missing or 

damaged, please contact the dealer immediately. Do 

not install a damaged or incomplete appliance.

Parts included with the dishwasher:

2-piece toe kick with sound insulation

• 

Cabinet mounting screws (2)

• 

Color-matched toe kick screws (2)

• 

Countertop mounting screws (2)

• 

Junction box cover and cover screw

• 

Leveling legs (2)

• 

Spanner wrench for leveling legs

• 

tools required for installation:

3/8”, 5/16” and 1/4” nut drivers

• 

Bucket

• 

Carpenter’s square

• 

Crescent wrench

• 

Drill and appropriate bits (new installations)

• 

Hole saw set (new installations)

• 

Level

• 

Phillips and flat blade screwdrivers

• 

Safety glasses

• 

Tape measure

• 

Tubing cutter

• 

Wire strippers

• 

Materials required for installation (not provided):
IMPORtANt:

 Do not use old parts.

90° elbow (3/8” NPT external thread on one end, 

• 

opposite end sized to fit water supply)
3 conductor wire (see electrical specifications)

• 

3 wire nuts to fit wire mentioned above. Additional wire 

• 

nuts may be required for connection to house wiring.
Air gap for drain hose (if required, see page 5)

• 

Hose clamp (depends on installation type)

• 

Shut-off valve (if not already installed)

• 

Thread seal tape, pipe seal tape or joint compound

• 

Water inlet line 3/8” minimum copper or 1/2” minimum 

• 

plastic (plastic must be tested for temperature and 

pressure). A new ferule and compression nut may also 

be required.
UL/CSA approved strain relief for electrical connection

• 

Y-branch tailpiece (if required, see page 5)

• 
Make sure you have everything necessary for proper 

installation before proceeding.

IMPORtANt:

 Each home installation differs. You may need 

parts in addition to those listed on this page to complete 

the installation.

Содержание Millennia EDW24

















Отзывы: