PLANNING
GUIDE
www.Dacor.com Phone: (800) 793-0093
Specifications subject to change without notice.
Install all appliances according to accompanying installation instructions.
5.9
Epicure
®
Ranges
ER30D, ER30DSR
ER30DSR with
H
J
K
no side panels no raised vent
23 1/2” (597 mm)
23 1/2” (597 mm)
24” to 25 9/16”
3-inch side panels* and no raised vent
20 1/2” (521 mm)
20 1/2” to 23 1/2”
21” to 25 9/16”
no side panels and raised vent
24” (610 mm)
24” (610 mm)
24 1/2” to 26 1/16”
3-inch side panels and raised vent
21” (533 mm)
21” to 24”
21 1/2” to 26 1/16”
Cutout tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated
toP VIEw - moDEL ER30DSR CoUNtERtoP/CAbINEt
CUtoUt DImENSIoNS SELf RImmING INStALLAtIoN
Non-combustible
rear wall recommeded
Countertop Height: Min: 35 5/8” (905 mm) Max: 37 3/8” (949 mm)
Combustible side
wall above range
countertop opening
29 1/2” (749 mm)
30” (762 mm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
overhang to width of
cabinets
1/4” Min. (6 mm)
Countertop
overhang
10” Min.
(254 mm)
both sides
Countertop front
H J K
rear wall recommended
Non-combustible
countertop opening
cabinet opening
below countertop
29 1/2” (749 mm)
27 1/2” (699 mm)
30” (762 mm)
2 3/8” (60 mm)
Combustible side
wall above range
10” Min.
(254 mm)
both sides
Countertop Height: Min: 35 5/8” (905 mm) Max: 37 1/4” (946 mm)
Notch countertop
overhang to width of
cabinets
3/8” Min. (10 mm)
Countertop
overhang
below countertop
Cabinet face
raised vent opening
H J K
Countertop front
toP VIEw - moDEL ER30DSR CoUNtERtoP/CAbINEt
CUtoUt DImENSIoNS, SELf RImmING INStALLAtIoN
wIth RAISED VENt (Atk30SR tRIm kIt INStALLED)
APPRoVED RAISED VENtS: ERV30 oR PRV30
Stiffener
Cabinet face*
Countertop*
*
IMPORTANT
: See Countertop/Cabinet Cutout Dimensions
for countertop cutout dimensions.
**
IMPORTANT
: If optional 3-inch side panels are not installed
cabinet face must be flush with back of control panel.
Back of
control
panel
ERV30 or
PRV30
raised vent
ER30DSR Range:
ATK30SR trim kit
required for installation
with raised vent
3/8” Min. (10 mm)
space behind
raised vent
chassis to clear
stiffener
Shown with
optional 3-inch
side panels
installed**
3/8” Min. (10 mm)
flat countertop overhang
required behind cutout
Countertop height:
35 5/8" (905 mm) Min.
37 1/4” (946 mm) Max.
Document # PG05-003
Revised 08/23/10 Page 3/3
