Dacor Epicure ERD30 Скачать руководство пользователя | Manualshive

Страница: 5 / 15

background image

Page 5

SPARK MODULE

REPAIR/REPLACEMENT

1. Remove grates, caps and burner rings

2. Using burner tool (86007C) remove brass nut (hold down ring) by turning

counter clockwise

3. Lift burner base out and disconnect electrode wire

4. Remove right and left vent cap

5. Lift off top frame

6. Remove insulation (there are scr ews on either side holding it down) and then

remove cover plate underneath the insulation.

**In some cases it may be necessary to remove the screws holding the burners

in place in or der to remove the cover plate

A. The Spark Module (part number 86526) is a 4 point ignition module and is

attached to the chassis with velcro

Figure 15-1

Figure 15-1 shows the cooktop area of the range (underneath the spilltray)

after the insulation and the cover plate have been removed.

A

«
...
3
4
5
6
7
...
»

Содержание Epicure ERD30
















Отзывы:

Нет отзывов

Похожие инструкции для Epicure ERD30

JGBP27DEMWW - 30" Gas Range

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

Бренд: GE Страницы: 52

Бренд: GE Страницы: 52

Бренд: Norge Страницы: 15

Designer DSCD13014B

Бренд: Viking Страницы: 14

Бренд: American Range Страницы: 1

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 24

Бренд: GE Страницы: 32

Бренд: Saturn Страницы: 17

Бренд: Saturn Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды