6
Oven Gripping Points
Repeat the mounting procedure for the lower
cavity if installing a double oven.
Installing the Exhaust Grill
With the oven now secured to the cabinet, install
the Exhaust Grill by mounting it to the oven with
the two screws provided.
NOTE:
You may need to loosen the side
mounting screws a little to align
the Exhaust Grill mounting holes.
Tighten the side mounting screws
after attaching the Exhaust Grill.
Exhaust Grill
#8 Screw
Attaching the Exhaust Grill
WARNING:
Failure to fully rotate the hinge
catches will cause them to bend
when the door is closed. This will
make closing the door impossible.
Secure oven to
cabinet with
screws provided
Single Ovens – 4 screws
Double Ovens – 6 screws
Installing the Cabinet Mounting Screws
Reinstalling the Oven Doors
WARNING:
Failure to fully rotate the hinge
catches will cause them to bend
when the door is closed. This will
make closing the door impossible.
Grasp the oven door on opposite sides and
lift it until the door hinges are aligned with the
openings in the oven frame. Holding the door at
about a 30˚ angle from the horizontal, slide the
hinges into the openings until the bottom hinge
arms drop fully into the hinge receptacles. Lower
the door to the fully opened position, and then
rotate the two hinge catches toward the oven.
Open and close the door completely to ensure
that it is properly installed.
Verifying Oven Operation
Slide the oven racks onto the support racks
within the cavity. Place the broiler pan and tray
on a rack within the oven, if desired.
Turn on the power supply to the oven. Set the
time of day by pressing the Clock touch pad
then pressing the TIME•TEMP key.
Press the BAKE selector pad for the upper oven
or single oven. Select a temperature of 350˚F
by pressing the TIME•TEMP “+” key. The oven
should now be heating. After approximately
three (3) minutes, the lower heating element
should glow red. Press the CANCEL•SECURE
pad to stop the oven heating process. It may
take longer than three (3) minutes when ovens
are running at voltages lower than 240V. If
checking the operation of the double oven,
repeat the bake test for the lower oven.
Press the BROIL selector pad for the upper
oven or single oven. Select a temperature of
350˚F by pressing the TIME•TEMP “+” key. The
oven should now be heating. After approximately
three (3) minutes, the upper heating element
should glow red. Press the CANCEL•SECURE
pad to stop the oven heating process. It may
take longer than three (3) minutes when ovens
are running at voltages lower than 240V. If
checking the operation of the double oven,
repeat the broil test for the lower oven.
WARNINGS:
If the oven does not operate
properly, follow these
troubleshooting steps:
1. Verify that power is being
supplied to the oven.
2. Check the electrical
connections to ensure that
the installation has been
completed correctly.
3. Repeat the above bake test.
4. If the appliance still does
not work, contact an
authorized DACOR service
company at (800) 772-7778.
Do not attempt to repair the
appliance yourself. DACOR
is not responsible for service
required to correct a faulty
installation.
NOTE:
You may need to loosen the side
mounting screws a little to align
the Exhaust Grill mounting holes.
Tighten the side mounting screws
after attaching the Exhaust Grill.
For double ovens, complete Verifying Oven
Operation for both the upper and lower doors.
For stainless steel ovens, peel off the protective
layer of plastic that covers the door panel.
Lift the wall oven up to the cabinet cutout, using
the upper edge of the cavity opening and the
bottom of the oven case side as gripping points.
Use extreme caution when lifting the appliance
as it is heavy. Be certain to take all necessary
safety precautions.
Resting the oven on the cabinet-mounting
platform, slide the oven into the recessed area
until the rear edge of the oven frame is flush
with the cabinet face and the oven is centered
within the cutout. Ensure that the electrical
conduit slides through the opening in the cabinet
platform or coils above the oven chassis as
the oven is slid into place. The cable must be
placed into the recessed area located along the
rear vertical edge of the oven or coiled above
the oven chassis. Do not trap the appliance
cable between the oven case back and the rear
wall.
For the single ovens and the upper cavity of the
double ovens, locate the mounting holes found
in the sides of the oven frame. Using a 1/16”
drill, drill four pilot holes for the #6 x 3/4” screws
provided in the instruction envelope. Install the
screws through the oven frame and into the
cabinet to secure the oven. Do not over-tighten
the screws.
