Dacor DR30GS, Руководство по установке

Страница: 12 / 24

10
Attaching the bracket to a concrete floor:
• Drill four (4) 3/8” diameter countersink holes through
any existing floor covering to the concrete slab below.
• Drill the 4 holes for the anchors 1 1/4” (3.2 cm) deep
into the concrete slab using a 3/16” masonry bit. This
hole length is longer than the anchor, but is required
for proper installation. Clear the holes of dust and any
other material. Tap each anchor into the hole until the
anchor top is flush with the top of the concrete slab.
Position the anti-tip bracket holes over the anchor
holes. Insert the screws through the four (4) holes
in the base of the bracket and thread them into the
anchors. Be sure the screw threads fully engage the
anchor body. Tighten the screws into place.
Attaching the bracket to a wood floor:
• If there is ceramic, asphalt or other hard floor covering
over the wood below, drill four (4) countersink holes to
allow access to the wood below for drilling pilot holes.
• Drill four (4) pilot holes into the wood floor using a drill
bit (1/16” dia. for #8 screws, 1/8” dia. for #12 screws).
Position the anti-tip bracket holes over the holes in the
floor. Insert the screws into the wood and tighten into
place.
CL
Installing the Anti-Tip Bracket on the Floor
(cont.)
Four (4) plastic anchors are provided along with three sizes
(4 each) of #8 or #12 Phillips head screws for attaching
the anti-tip bracket to the floor. Use both the anchors and
four (4) of the #8 screws when attaching the bracket to a
concrete sub-floor. Do not use the anchors when attaching
to a wood sub-floor.
1. Determine the location of the range center line and
front panel when the range is in its final position
based on the Product Dimensions on page 4
and the actual cabinet/cutout dimensions used for the
installation.
2. Determine the required position of the anti-tip bracket,
based on the diagram, bottom right. Mark the four (4)
mounting hole locations on the floor with a pencil.
3. Determine the screw size required. The minimum full
thread depth (portion of screw threaded into wood/slab)
for wood is 3/8” (1 cm) and 5/8” (1.6 cm) for concrete.
See the table below to select the correct screw size.
Sub-Floor Type/
Floor Covering Thickness
Screw Size
Concrete or wood sub-floor,
no floor covering over top.
#8 x 1 *
Concrete or wood sub-floor,
floor covering up to 1/4” thick
#8 x 1 *
Concrete or wood sub-floor,
floor covering over 1/4” and
up to 1/2” thick
#8 x 1 1/4 *
Wood sub-floor, floor covering
over 1/2” and up to 1 3/16”
thick
#12 x 1 3/4 *
Concrete sub-floor under floor
covering over 1/2” thick
Must be purchased
separately **
Wood sub-floor, floor covering
over 1 3/16” thick
Must be purchased
separately **
* Included with range
** Determine required depth based on information in step 3
and purchase from local hardware store.
Installation Instructions
#8 x 1”, #8 x 1 1/4”
or #12 x 1 3/4
screw, 4 places
(see text)
Anchor, 4 places:
use for concrete
floor only
Front hole
Anti-tip bracket
front hole
locations
Range front
panel
Range center line
10 3/8” (26.4 cm)
2 3/16” (5.6 cm)
Cabinet
face below
countertop
22 1/2”
(57.2 cm)
Top View
Anti-tip
bracket
Sub-floor
Floor
covering
Concrete
anchors shown,
do not use for
wood sub-floor
Screws attached
to sub-floor below
floor covering
Side View