background image

TROUBLESHOOTING

SYMPTOM

1. Screen or mask will not operate. 

Motor does 

not

hum.

Motor

hums.

CAUSE

(a) Blown facility fuse.

(b) Tripped facility circuit breaker.

(c)

No power

to receptacle in junction

box.

(d) No power to bus interface unit.

(e) Loose control wire connections

Power at junction box

(f) Thermal overload tripped.

(g) Transformer not plugged in.

(h) Defective motor.

(i)

Temporary binding.

SOLUTION

(a) Replace facility fuse.

(b) Reset facility circuit breaker.

(c) Check above. Tighten all loose

wire connections. Recheck
wiring. See installation
instructions.

(d) Make sure transformer is

connected to bus interface – see
wiring diagram.
Defective transformer – replace.

(e) Check all T4 and T6 wire

connections – see wiring
diagram.

(f) Let motor cool down for 15

minutes. Try again.

(g) Plug transformer into receptacle

on non-motor end of screen.

(h) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(i)

With power 

“off,”

turn roller by

hand to free binding.

2. Image on screen does not match

picture area.

(a) Screen not set to the correct

format.

(b) Screen or mask out of

adjustment.

(a) Set screen to the format being

projected.

(b) See screen adjustment. We

recommend you have your dealer
make these adjustments for you.

6

3. Noise.

NOTE: Screen will operate with a
low-pitched hum.

(a) Grinding. Foreign object in screen

rubbing on roller or fabric.

(a) Remove.

4. Coasting.

(a) Defective brake.

(a) Replace motor assembly.

5. Fabric hangs crooked.

(a) Screen not installed properly.

(b) Fabric has backed up inside case.

(c) Fabric is damaged.

(a) Check for level and plumb.

(b) Lower screen and carefully pull

fabric to remove any slack on the
roller.

(c) Replace fabric.

Содержание TENSIONED HORIZON ELECTROL









Отзывы: