Da-Lite ADVANTAGE ELECTROL Скачать руководство пользователя страница 12

Страница: 12 / 16

Third Party Control

Control Panel

A control panel may be connected to the splitter board by using
the dry contact Up, Down and Common connections. The
control panel must provide a momentary, dry contact closure of
at least 1/2 second.

1. Use 3-conductor 20-24 gauge wire to connect the control panel

to the splitter board.

2. A momentary closure across the common and up wires will be

an “up” command.

3. A momentary closure across the common and down wires will

be a “down” command.

4. A momentary closure across the common, up and down wires

will be a “stop” command.

Operation of Screen

Operation & Limit Adjustment Wall Switch

1. Press ”DOWN” button on screen switch and screen will deploy

out of case in downward direction.

2. Press “STOP “button on screen switch and screen will stop if in

movement.

3. Press “UP” button on screen switch and screen will retract

upward into case.

“Up”

Button

“Stop”

Button

“Down”

Button

“Up”

Button

“Down”

Button

European Style Wall Switch (220V models only)

1. Press ”DOWN” button on screen switch and screen will deploy

out of case in downward direction.

2. Press “UP” button on screen switch and screen will retract

upward into case.

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)
5V (Bus)

Содержание ADVANTAGE ELECTROL

















Результаты поиска

Содержание ADVANTAGE ELECTROL

Отзывы:

Похожие инструкции для ADVANTAGE ELECTROL

Бренды по названию

Популярные бренды

Da-Lite ADVANTAGE ELECTROL, Инструкция

Результаты поиска

Содержание ADVANTAGE ELECTROL

Отзывы:

Похожие инструкции для ADVANTAGE ELECTROL

Бренды по названию

Популярные бренды