D.W. Fearn VT-1 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

D.W. Fearn VT-1 Скачать руководство пользователя страница 17

D.W. FEARN

VT-1 & VT-2 Microphone Preamplifers

17

2 .

D E S C R I P T I O N

The Model VT-1 and VT-2 Vacuum Tube Microphone Preamplifiers are designed to provide
recording professionals with a sonically superior input device. (Unless there is a specific rea-
son to address a difference between the VT-1 and VT-2 preamplifiers, the device will be
referred to as the “VT-2.”) It is typically used in sound recording studios for recording indi-
vidual tracks. A quality microphone is connected to a VT-2 input, and the VT-2 provides a
line-level output. In most situations, the VT-2 will feed directly to the input of the recorder.

The VT-2 is a recreation of the classic tube preamps of the 1960s, updated with improved
modern passive components and computer-aided circuit optimization. Because of the unique
qualities of vacuum tubes, the VT-2 has a clarity, transparency, and warmth that solid state
preamps lack. Its modern design and construction allows the VT-2 to exceed the per-
formance of vintage vacuum tube preamps.

It is designed for use in the professional recording environment. It accepts all low impedance
balanced microphones. It features a reg48 volt supply for phantom powering con-
denser microphones, a switchable 20 dB input pad, a phase (polarity) reversal switch, a
switchable input network to accommodate very low impedance microphones (typically trans-
formerless types), and a true VU meter. It is built to sound great for a long time, with top qual-
ity parts used throughout; all the transformers and many other components are custom-made
for the VT-2.

All four power supplies (filament, phantom power, B+, and meter amp) are solid state and
fully regulated. The Attenuation control potentiometer is a conductive plastic type for long,
noise-free operation.

The VT-2 is not mass-produced. Each one is hand-made and meticulously tested and listened
to before shipment to the customer.

«
...
15
16
17
18
19
...
»

Содержание VT-1









































Отзывы:

Нет отзывов