D-Link DWR-980 Скачать руководство пользователя

Страница: 10 / 266

DWR-980

Wireless AC1200 4G LTE Router with VDSL2 Support,

Gigabit Ethernet Ports, and 2 FXS Ports

User Manual

Overview

LTE Module Parameters

LTE connection rate

Downlink: up to 150Mbps

Uplink: up to 50Mbps

Supported frequencies

Power Class 3

LTE
B1/2/3/5/7/8/20/38/40

UMTS
B1/2/3/5/8 (2100/1900/1800/850/900MHz)

GSM/GPRS
850/900/1800/1900MHz

Functions

Auto connection to available type of supported network (4G/3G/2G)

Auto configuration of connection upon plugging in SIM card

Enabling/disabling PIN code check, changing PIN code

Sending/receiving/reading/removing SMS messages

DSL Parameters

VDSL/ADSL Standards

VDSL2: ITU G.993.2, support of 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a, 35b

ADSL: Multi-mode, ANSI T1.413 Issue 2, ITU-T G.992.1 (G.dmt) Annex A, ITU-
T G.992.2 (G.lite) Annex A, ITU-T G.994.1 (G.hs)

ADSL2: ITU-T G.992.3 (G.dmt.bis) Annex A/L/M, ITU-T G.992.4 (G.lite.bis)
Annex A

ADSL2+: ITU-T G.992.5 Annex A/L/M

ATM/PPP Protocols

Bridged and routed Ethernet encapsulation

VC-based or LLC-based multiplexing

ATM Forum UNI3.1/4.0 PVC (up to 8 PVCs)

ATM Adaptation Layer Type 5 (AAL5)

ITU-T I.610 OAM F4/F5 loopback

ATM QoS

PPP over ATM (RFC 2364)

PPP over Ethernet (PPPoE)

Keep-alive for PPP connections

Data rates are theoretical. Data transfer rate depends on network capacity and signal strength.

Supported frequency bands are dependent on regional variants.

Page

of 266

Содержание DWR-980











































































































































































































































































Результаты поиска

Содержание DWR-980

Отзывы:

Похожие инструкции для DWR-980

Бренды по названию

Популярные бренды

D-Link DWR-980, Руководство пользователя

Результаты поиска

Содержание DWR-980

Отзывы:

Похожие инструкции для DWR-980

Бренды по названию

Популярные бренды