D-Link DPN-1021G Скачать руководство пользователя страница 110

Страница: 110 / 145

DPN-1021G

GPON ONT VoIP Gateway with 1 GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

Call Feature Codes

On the

VoIP / Call Feature Codes

page, you can allow changing some parameters of the

gateway directly from the phone set connected to the FXS port of the gateway.

Figure 80. The

VoIP / Call Feature Codes

page.

The following call feature codes are available:

Parameter

Description

Disable Call Waiting

Disables the call waiting function.

Enable Call Waiting

Enables the call waiting function.

Disable Do Not Disturb

Disables rejection of incoming calls.

Enable Do Not Disturb

Enables rejection of all incoming calls (the busy tone
will be heard).

Enable Call Forwarding No

Answer

Enables call forwarding when this line gives no reply.

Disable Call Forwarding No

Answer

Disables call forwarding when this line gives no reply.

Enable Call Forwarding On Busy

Enables call forwarding when this line is busy.

Disable Call Forwarding On Busy

Disables call forwarding when this line is busy.

Enable Unconditional forwarding

Enables forwarding for all calls.

Disable Unconditional forwarding

Disables forwarding for all calls.

Page

110

of 145

Содержание DPN-1021G


















































































































































Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды

D-Link DPN-1021G, Руководство пользователя

Результаты поиска

Содержание DPN-1021G

Отзывы:

Похожие инструкции для DPN-1021G

Бренды по названию

Популярные бренды