RC3A12 RF REMOTE, TRI-ZONE
Thank you for choosing Cyron products!
At Cyron we
are committed to provide the latest lighting technology
without any compromises. Please read instructions
completely before starting installation.
TOOLS NEEDED:
Wire stripper, W ire cutter, Electrical tape, Connector
Crimper may be used.
INSTRUCTIONS:
Follow the wiring diagram below to
install the remote. It is best to make the 12VDC power
connection directly to the battery posts. Remove fuse
from fuse holder during the installation process. Make all
connections securely, following proper electrical
practices. Keep wires away from excess heat and
moving parts. Consult your vehicle owners manual if you
would like to connect to accessory switches. Do not
exceed max current capacity and power rating of vehicle
accessories.
Cyron RC3A12 is able to operate in basic mode (Uni-
Zone) or advance mode (Tri-Zone). In the Uni-Zone
mode all the lights work together with a simple on/off
operation. In this mode buttons 2, 3, 4 of the remote are
deactivated.
In the Tri-Zone mode three zones (groups) of LEDs work almost independently. For example in a motorcycle lighting project Zone1 can
be the lights around the motor, Zone2 can be the ground effect lights, and Zone3 can be lights in the wheels. Each controller channel is
dedicated to a zone of lights. In fact, each zone can be any 12VDC LED that draws 3Amp or less.
IMPORTANT
: Total controller capacity is 3x 3A or 9A. Do not exceed this rating. Serious damage to controller and wiring will be
caused.
OPERATIONS:
Pair Up Remote:
The first step is to pair up the remote to the controller. With all wiring completed remove the fuse
from fuse holder. Replace fuse back and within 5 seconds press button 1 three consecutive times. All channels should flash 5 times
confirming the pair up process. If not successful repeat process again.
Operation Modes:
The controller presently is either Uni-Zone or Tri-Zone modes. Test by pressing
button 2 to see if any changes in lights take place. If pressing 2 does not change the lights the
remote is in Uni-Zone mode. If the lights do change the remote is in Tri-Zone mode.
Change from Uni-Zone to Tri-Zone:
1. Turn the lights off using Button 1.
2. Press and hold buttons 3 and 4 for one second.
3. Ch2 will flash 5 times to confirm.
Change from Tri-Zone to Uni-Zone:
1. Turn the lights off using Button 1.
2. Press and hold buttons 1 and 2 for one second.
3. Ch1 will flash 5 times to confirm.
A vast array of features are available in Tri-Zone mode. There are 10 light modes, 5 static and 5 dynamic. In Static modes the lights
are on solid without any movement. In Dynamic modes the lights (channels) go through a pre-programmed sequence of patterns which
are appropriately named in the chart below. Speeds of the patterns are adjustable by pressing button 3 to decrease and button 4 to
increase. There are 5 speeds in each Dynamic mode.
Brake light trigger/Aux Wire:
This feature will make the accent light system become a safety or deterrent feature. Connecting Aux W ire
to +12VDC will turn on Channel 3 regardless if the controller is on or off. For instance, connect Au x wire to brake lights and every time
brakes are applied the lights of Ch3 can be additional visual signal. NOTE: Consult with your local laws regarding additional driving
lights on vehicles. Another usage can be connecting Aux wire to
output of an alarm system. Ch3 would turn on when alarm is
triggered.
Battery Saver:
Controller will cut off the light system if the supply
voltage (vehicle battery) drops too low, preserving the battery for
starting the vehicle. With this feature the lights can be left on without
worrying about a dead battery. This feature does not apply to 24VDC
supply voltage.
Modes in Tri-Zone
(button 2 to change)
Channel
1
Channel
2
Channel
3
1 (Static)
ON
ON
ON
2 (Static)
ON
ON
OFF
3 (Static)
ON
OFF
OFF
4 (Static)
OFF
ON
ON
5 (Static)
OFF
OFF
ON
6 (Dynamic)
SHOW OFF
7 (Dynamic)
BRING IT ON
8 (Dynamic)
HEART BEAT
9 (Dynamic)
KNOCKOUT
10 (Dynamic)
BLIND SHOT
