Cypress PSoC CY8C23533 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 410

Cypress PSoC CY8C23533 Скачать руководство пользователя страница 83

Document # 001-20559 Rev. *D

19

9.

Internal Low Speed Oscillator

(ILO)

This chapter briefly explains the Internal Low Speed Oscillator (ILO) and its associated register. The Internal Low Speed
Oscillator produces a 32 kHz clock. For a quick reference of all PSoC registers in address order, refer to the

Details chapter on page 47

9.1

Architectural Description

The Internal Low Speed Oscillator (ILO) is an oscillator with
a nominal frequency of 32 kHz. It is used to generate sleep
wake-up interrupts and watchdog resets. This oscillator can
also be used as a clocking source for the digital PSoC
blocks.

The oscillator operates in three modes: normal power, low
power, and off. The normal power mode consumes more
current to produce a more accurate frequency. The low
power mode is always used when the part is in a power
down (sleep) state.

9.2

Register Definitions

The following register is associated with the Internal Low Speed Oscillator (ILO). The register description has an associated
register table showing the bit structure. The bits in the table that are grayed out are reserved bits and are not detailed in the
register description that follows. Note that reserved bits should always be written with a value of ‘0’.

9.2.1

ILO_TR Register

The Internal Low Speed Oscillator Trim Register (ILO_TR)
sets the adjustment for the internal low speed oscillator.

The device-specific value, placed in the trim bits of this reg-
ister at boot time, is based on factory testing.

It is strongly

recommended that the user not alter the values in the
register

.

Bits 5 and 4: Bias Trim[1:0].

These two bits are used to

set the bias current in the PTAT Current Source. Bit 5 gets
inverted, so that a medium bias is selected when both bits
are ‘0’. The

bias current

is set according to

Bits 3 to 0: Freq Trim[3:0].

These four bits are used to

trim the frequency. Bit 0 is the LSb and bit 3 is the MSb. Bit 3
gets inverted inside the register.

For additional information, refer to the

ILO_TR register on

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

1,E9h

Bias Trim[1:0]

Freq Trim[3:0]

W : 00

Table 9-1. Bias Current in PTAT

Bias Current

Bias Trim [1:0]

Medium Bias

00b

Maximum Bias

01b

Minimum Bias

10b

Reserved 11b

«
...
81
82
83
84
85
...
»

Содержание PSoC CY8C23533



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды