Cypress CY8CPROTO-064B0S3 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 47

background image

CY8CPROTO-064B0S3 PSoC 64 "Secure Boot" Prototyping Kit Guide, Doc. # 002-29505 Rev. *B

19

Kit Operation

3.2

KitProg3

The  PSoC  64  “Secure  Boot”  Prototyping  Board  can  be  programmed  and  debugged  using  the
onboard  KitProg3.  KitProg3  also  has  USB-UART  and  USB-I2C  functionality.  KitProg3  supports
CMSIS-DAP  Bulk  mode  and  DAPLink  mode  for  programming  the  target  MCU  using  SWD.  A

Cypress PSoC 5LP device is used to implement KitProg3 functionality. For more details on the

KitProg3 functionality, see the

KitProg3 User Guide

3.2.1

Programming and Debugging

This section presents a quick overview on how to connect the kit and select the KitProg3 mode for
programming and debugging. For detailed instructions, see

Help

>

ModusToolbox IDE

Documentation

>

User Guide

.

Connect  the  board  to  the  PC  using  the  USB  cable  at  KitProg3  USB  connector  J8.  The  kit
enumerates as a composite device if you are connecting it to your PC for the first time. KitProg3 can
operate  either  in  CMSIS-DAP  Bulk  mode  or  DAPLink  mode  (default).  ModusToolbox  requires
CMSIS-DAP  Bulk  mode  to  program  or  debug  the  device  while  the  provisioning  process  requires
DAPLink mode. The status LED (Amber) is always ON in CMSIS-DAP Bulk mode and ramping ON/
OFF at a 2-Hz rate in DAPLink mode. Press the Mode Switch and release quickly to switch between

these modes. If you do not see the desired LED status, see the

KitProg3 User Guide

for details on

the KitProg3 status and troubleshooting instructions.

3.2.2

USB-UART Bridge

The KitProg3 on the board can act as a USB-UART bridge. The UART lines between the PSoC 64
device and KitProg3 are hard-wired on the board, as

shows. For more details on the

KitProg3 USB-UART functionality, see the

KitProg3 User Guide

.

Figure 3-4. UART Connection between KitProg3 and PSoC 64 Device

P12[6]
P12[7]

USB

KitProg3

PSoC 64

P5[0]
P5[1]

UART

UART_TX

UART_RX

TX

RX

TX

RX

«
...
18
19
20
21
22
...
»

Содержание CY8CPROTO-064B0S3
















































Отзывы:

Нет отзывов

Похожие инструкции для CY8CPROTO-064B0S3

Бренд: Atmel Страницы: 22

Бренд: NXP Semiconductors Страницы: 12

SuperServer SYS-E102-9AP-LN4-C

Бренд: Supermicro Страницы: 81

Бренд: DFI Страницы: 8

Бренд: Fujitsu Siemens Computers Страницы: 42

Бренд: Gigabyte Страницы: 120

GeForce 8300 (MI-A78U-8309)

Бренд: XFX Страницы: 26

Бренд: Intel Страницы: 78

Бренд: NXP Semiconductors Страницы: 32

Бренд: Fairchild Страницы: 17

Kontron pITX-iMX8M

Бренд: S&T Страницы: 65

Бренд: Intel Страницы: 113

Бренд: JETWAY Страницы: 48

Бренд: ICP Страницы: 50

Бренд: AOpen Страницы: 8

Бренд: YASKAWA Страницы: 28

P5B PRO - QUICK

Бренд: ASROCK Страницы: 48

DS320PR412-421EVM

Бренд: Texas Instruments Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды