Cypress CY4603 Скачать руководство пользователя страница 26

Страница: 26 / 94

HX3 Kits User Guide, Doc. #: 001-91203 Rev. *D

Kit Operation

Note

: The Device Manager listing for the USB 3.0 and USB 2.0 MTT hubs can vary based on the

host or OS implementation.

4. In the

USB 3.0 Hub Properties

window, select the

Details

tab and choose

Hardware Ids

from

the drop-down list. The Cypress VID and PID are displayed, as shown in

Figure 3-14

Figure 3-14. VID and PID for CY4609

Table 3-5

describes the VID and PID values for USB 2.0 and USB 3.0 hubs.

Note:

The DID value displayed in

Figure 3-14

may vary depending up on the HX3 firmware version.

3.4.3

USB 3.0 Data Transfer

1. Get a USB 3.0-certified flash drive and store a 2-GB file. Connect the flash drive to one of the

downstream ports, as shown in

Figure 3-15

. For the CY4613 board, connect the flash drive to a

standard USB 3.0 downstream port or to a Shared Link SS downstream port.

2. Copy the 2-GB file from the flash drive to the PC to transfer data in the USB 3.0 SuperSpeed

mode.

Table 3-5. VID and PID Values of HX3 Kits

Kit

Hub Type

VID (hex)

PID (hex)

CY4609

USB 3.0

04B4

6500

USB 2.0 MTT

6502

CY4603

USB 3.0

6504

USB 2.0 MTT

6506

CY4613

USB 3.0

6508

USB 2.0 MTT

650A

VID: 04B4
PID:6500

DID: 501A

Содержание CY4603































































































Результаты поиска

Содержание CY4603

Отзывы:

Похожие инструкции для CY4603

Бренды по названию

Популярные бренды

Cypress CY4603, Руководство пользователя

Результаты поиска

Содержание CY4603

Отзывы:

Похожие инструкции для CY4603

Бренды по названию

Популярные бренды