manualshive.com logo in svg

Cypress CY3631, Руководство пользователя

Поделиться
Скачать
Cypress CY3631 Скачать руководство пользователя страница 19

CY3631 WirelessUSB™ Manufacturing Test Kit  User Guide, Doc. # 001-66724 Rev. *B

19

1.

Appendix 

1.1

Appendix - A

1.1.1

Using the Command Line Interface

The default serial port settings for the test fixture are 9600, N, 8, 1, NONE, with local echo turned on
in the terminal emulator of choice. When power is applied to the test fixture, the following welcome
banner comes up in the terminal window.

******************************************************************************

WirelessUSB Tester - v1.0

                                                            For help, type: he

******************************************************************************

MTK>

If this banner is not displayed, then recheck the serial port connection and settings.

All serial port commands are case insensitive. While the help menu displays commands in upper
case, they may be entered in lower case. The PD command requires parameters to be entered in
hexadecimal format without any prefix or postfix characters (see the help menu for an example.) The
letters in the hexadecimal numbers may be lowercase as well.

A listing of all the supported commands with parameter limits is displayed by typing the command
HE as shown in the welcome banner. Following is an output example of the help menu.

MTK> he

 

 

TESTER HELP MENU

******************************************************************************

All commands and parameters are case insensitive. The following commands are executed immedi-
ately:

Show This Help Menu ........................... HE

Show Current Tester Settings .................. CS

Execute Standard Test ......................... ST

Set Channel, PN Code, Power, Correlator ....... SC <0-77> <0-7> <0-7> 

<0-16>

Transmit Carrier for N seconds, 0 = infinite .. TC <0-255>

Transmit Random for N seconds, 0 = infinite ... TR <0-255>

Send Data to DUT, e.g. PD 5A 00 0A FF 34 ...... PD <B1 B2 ... B15>

Tester Crystal Adjust (stored in EEPROM) ...... CA <0-63>

Crystal Clock Output ON=1/OFF=0 ............... XO <0-1>

Restore Default Settings to EEPROM ............ RE

Содержание CY3631
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды