CYBEX CardioTouch 770T Скачать руководство пользователя страница 42

Страница: 42 / 261

C.A.B. (Console Adapter Box) or Connected TV setup option

Access setup screen.

Press and hold Cybex logo for 6 seconds to ac-
cess

Screen Lock

and

Toolbox

CYBEX LOGO

Press and hold language logo for 6 seconds to
access

Screen Lock

and

Toolbox

LANGUAGE ICON

Tap the

Access Toolbox

icon to display the

Access to Toolbox

Enter the sequence:

Tap

Setup

at the main

Toolbox

screen.

Tap the

Shift Right

icon to navigate to the

TV Source

icon.

Tap

Device Installed

to select A/V type.

Select C.A.B. (Console Adapter Box) or Connected TV from the A/V options.

Tap the

Toolbox

icon to return to the

Toolbox

screen.

Adjust volume

Plug headphones into headphone jack.

Listen to the TV audio. At the default volume level of 10 on the unit, the TV volume should be ‘normal’.

If the TV is too loud or too quiet, adjust the TV volume using the Broadcast Vision Remote Control
or controls on the TV until it is acceptable.

Adjust the volume on the unit using the Volume Up/Down buttons to ensure a normal range for use.

Once the TV volume is set, apply this TV volume level to all TV’s.

Setup Complete

Embedded TV Setup

The embedded TV configuration uses the E3 View Monitor in the console of the product.

Page 42 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды