manualshive.com logo in svg

Cybertech A822P, Руководство по эксплуатации продукта

Поделиться
Скачать
Cybertech A822P Скачать руководство пользователя страница 16

 

CONFIGURATION PARAMETERS 

 

4.2.14 SET HANDSHAKE TYPE (1B 48 x)

 

   If this sequence is received the handshake can be changed. If 
a "0" is received the unit is set to Hardware handshake, if a "1" 
is received the unit is set to Software handshake. This is a semi 
permanent stored byte internal to the microprocessor's EEprom. 
 

4.2.15 SET BAUD RATE (1B 52 x)

 

   WARNING - THIS WILL CHANGE THE UNITS OPERATING BAUD RATE SEMI-
PERMANENTLY (POWER ON/OFF WILL NOT AFFECT THIS). When this 
sequence is received the units operating baud rate will be 
changed. x should be 0 through 6 and corresponds to 300 through 
19200– see chart below.  This is a semi-permanent stored byte 
internal to the microprocessor's EEprom. The default baud rate is 
9600, when shipped from the factory (unless otherwise requested). 
 
 

 

Baud Rate Code Chart  

 

Baud Rate code 

Actual Baud Rate 

0 300 
1 600 
2 1200 
3 2400 
4 4800 
5 9600 
6 

19200

Содержание A822P






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды