CyberData RAL 9003 Скачать руководство пользователя

Страница: 11 / 126

Product Overview

Product Features

Operations Guide

931260A

CyberData Corporation

1.3 Product Features

SIP Features

•

Singlewire speakers now offer dual registration for both SIP and Singlewire

•

Full-duplex (SIP) or half-duplex (push to talk)

•

Support for security code to prevent unwanted SIP calls

•

Optional red/green/blue/white strobe kit connection available (coming soon)

•

Autoprovisioning via HTTP, HTTPS, or TFTP

•

HTTPS or HTTP web based configuration. HTTPS is enabled by default.

•

802.11q VLAN tagging

•

Configurable sense input for use with fault detection or with optional lighted button kit

•

Configurable event generation for device health and status monitoring

•

Support for G.711 u-law, G.711 a-law, and G.722 codecs.

•

Powered via PoE (802.3AF or 802.3AT) or 24V auxiliary power supply (not included)

•

Enhanced interoperability for hosted environments

•

Night Ringer function

•

Plays audio from Multicast

•

Web-based configuration

•

Paging prioritization and background music

•

User upgradeable firmware via web interface or autoprovisioning

•

External volume control

•

Small footprint

•

High efficiency speaker driver

•

IGMP l SIP endpoint or Multicast group member

•

Network-adjustable speaker volume

•

Optional auxiliary speaker available to increase audio coverage - Part #011120/011121

•

Optional clock kit available - Part #011153/011154

•

Support for 10 multicast paging groups

•

Support for multiple SIP servers for redundancy

•

Support for Cisco SRST resiliency

•

Relay for activating door locks, external amplifiers, etc.

•

Line-level audio output for connecting to an external amplifier

Singlewire InformaCast Features

•

Singlewire Informacast compatibility available. Includes support for Informacast resiliency.

•

Supports both SIP and Singlewire InformaCast

•

InformaCast compliant

•

InformaCast CK compliant

Содержание RAL 9003































































































































Результаты поиска

Содержание RAL 9003

Отзывы:

Похожие инструкции для RAL 9003

Бренды по названию

Популярные бренды

CyberData RAL 9003, Руководство по эксплуатации

Результаты поиска

Содержание RAL 9003

Отзывы:

Похожие инструкции для RAL 9003

Бренды по названию

Популярные бренды