background image

YACK Operation Manual

Version MY181210

L - ULTIMATIC MODE

 Sets the keyer into ULTIMATIC mode. In Ultimatic mode always the last paddle to 

be touched is repeated indefinitely when paddles are squeezed

X - PADDLE SWAP

 DIT and DAH paddles are swapped.

F - FARNSWORTH PAUSE

 Allows setting of an extended inter-character pause in all playback modes which 

makes fast keying easier to understand. Note that this of course only influences RECEPTION, not 
TRANSMISSION. If you desire Farnsworth mode in transmission, please manually pause during characters.

COMMANDS – TRANSMITTING AND TONE

I - TX INVERT

 This function toggles whether the "active" level on the keyer output is positive or negative. 

This setting is dependent on any additional attached keying circuits or radios. Normally this command is left 
alone.

K - TX DISABLE

 Toggles the setting of the TX keyer output. In default state the keyer switches the transmit 

line when it is in keyer mode. Toggling this setting enables or disables that function. NOTE: Keying is always 
off in Command mode.

S - -SIDETONE 

The side tone oscillator setting is toggled (ON -> OFF or OFF -> ON). NOTE: This setting is 

only of relevance for regular keying mode. Side tone is always on in command mode.

COMMANDS – FEATURES

C - CALLSIGN TRAINER

 The keyer plays a generated 2x2 call signs (side tone only) at the current WPM 

setting. The call signs are then entered back using the iambic key. If it is repeated correctly, "R" is played and 
the next call sign is given. If a mistake was sensed, the error pro-sign (8 dots) is sounded and the current call 
sign is repeated again for the user to try once more. If nothing is keyed for 10 seconds, the keyer returns to 
command mode.

Z - ADVANCED TRAINER 

Similar to the training mode above except on each successful entry the speed is 

increased by 1WPM. An unsuccessful entry reduces the speed by 1WPM. Pressing the command button will 
terminate the training, return the keyer to the original WPM speed, and give statistics of speed at end of session,
number of calls sent, and number of calls correct. Do not press command mode while the keyer is sending. The 
last call sign sent is not counted.

N  - BEACON MODE

 The keyer responds with "N" after which a number between 0 and 9999 can be keyed. 

After a 5 second timeout the keyer responds by repeating the number and 'R'. Once the keyer returns to keyer 
mode, the content of message buffer 2 is repeated in intervals of the message length plus N seconds. The setting
is preserved in EEPROM so the chip can be used as a fox hunt keyer. Returning to command mode and entering
an interval of 0 (or none at all) stops beacon mode. Keyer will respond with 'R'.

Y - FOXHUNT MODE

 When toggling this command the transmitter output will stay keyed down the entire 

time a memory is played. Toggling again will resume the memories back into on-off-on keying mode. This 
command works along with the Beacon command to allow a setup, such as an FM transmitter, to be used as a 
beacon or fox hunting box.

Содержание Mini Yack IIc








Отзывы: