Custom Audio Electronics TK180, Краткое руководство

Страница: 35 / 36

The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this copy
Via Berettine 2/B
43010 Fontevivo (PARMA) - Italy
Tel. : +39 0521-680111
Fax : +39 0521-610701
http: www.custom.biz
Customer Service Department:
www.custom4u.it
© 2020 CUSTOM S.p.A. – Italy. All rights reserved. Total or partial repro-
duction of this manual in whatever form, whether by printed or electronic
in it has been carefully checked, CUSTOM S.p.A. and other entities
utilized in the realization of this manual bear no responsibility for how
Information regarding any errors found in it or suggestions on how it could
changes in information contained in this manual without prior notii cation.
The pre-installed multimedia contents are protected from Copyright
CUSTOM S.p.A. Other company and product names mentioned herein
may be trademarks of their respective companies. Mention of third-party
products is for informational purposes only and constitutes neither an
responsibility with regard to the performance or use of these products.
CUSTOM S.p.A. declines all responsibility for accidents or damage to
persons or property occurring as a result of tampering, structural or func-
tional modii cations, unsuitable or incorrect installations, environments not
in keeping with the equipment’s protection degree or with the required
temperature and humidity conditions, failure to carry out maintenance
and periodical inspections and poor repair work.
REQUIREMENTS.
The device is in conformity with the essential Electromagnetic Compat-
ibility and Electric Safety requirements laid down in Directives 2014/30/
EU and 2014/35/EU inasmuch as it was designed in conformity with the
provisions laid down in the following Standards:
The device is in conformity with the essential requirements laid down in
Directives 2014/53/EU about devices equipped with intentional radiators
The Declaration of Conformity and other available certii cations can be
downloaded from the site www.custom4u.it.
products shall NOT be mixed with unsorted municipal waste. For more
detailed information about recycling of this product, refer to the instruc-
tions of your country for the disposal of these products.
waste, but arrange to have it collected separately.
The re-use or correct recycling of the electronic and electrical equip-
wellbeing of humans.
In accordance with European Directive WEEE 2012/19/EU, special
collection points are available to which to deliver waste electrical and
distributor at the moment of purchasing a new equivalent type.
recovery of waste electrical and electronic equipment through the or-
Unauthorised disposal of waste electrical and electronic equipment is
punishable by law with the appropriate penalties.
Your attention is drawn to the following actions that could compromise
the characteristics of the product:
Read and retain the instructions which follow.
Follow all indications and instructions given on the device.
Make sure that the surface on which the device rests is stable. If it is
not, the device could fall, seriously damaging it.
that there is suffi cient ventilation.
Do not i x indissolubly the device or its accessories such as power
supplies unless specii cally provided in this manual.
[Only OEM equipment] The equipment must be installed in a kiosk or
system that provides mechanical, electrical and i re protection.
The mains power supply must comply with the rules in force in the
Country where you intend to install the equipment.
Make sure that there is an easily-accessible outlet with a capacity of no
less than 10A closely to where the device is to be installed.
Make sure the power cable provided with the appliance, or that you
intend to use is suitable with the wall socket available in the system.
Make sure the electrical system that supplies power to the device is
equipped with a ground wire and is protected by a dif erential switch.
Before any type of work is done on the machine, disconnect the power
supply.
Use the type of electrical power supply indicated on the device label.
These devices are intended to be powered by a separately certi-
i ed power module having an SELV, non-energy hazardous output.
[Only POS equipment] The energy to the equipment must be provided
by power supply approved by CUSTOM S.p.A.
lary components.
Do not carry out repairs on the device yourself, except for the normal
The equipment must be accessible on these components only to
Periodically perform scheduled maintenance on the device to avoid dirt
Do not touch the head heating line with bare hands or metal objects. Do
not perform any operation inside the printer immediately after printing
because the head and motor tend to become very hot.
Use consumables approved by CUSTOM S.p.A.