Custom Audio Electronics SKANER A4 Скачать руководство пользователя | Manualshive

Страница: 19 / 44

background image

3.4 Driver and SDK

The drivers are available for the following operating system:

OPERATING
SYSTEM

DESCRIPTION

INSTALLATION PROCEDURE

Windows

Driver for Windows 7 (32/64 bit)

From the Start menu, press Run

and type-in the path where the SW

was saved on your PC, then click OK.

Follow the instructions that appear

on the screen to install the driver.

Driver for Windows 8 (32/64 bit)

Driver for Windows 8.1 (32/64 bit)

Driver for Windows 10 (32/64 bit)

Windows

CuDoubleSidedScannerAPI DLL for .NET

Extract the zipped folder to

the destination path desired.

Follow the instructions present

in the software package that you

downloaded on how to install

and use the library.

CuDoubleSidedScannerAPI DLL for C++

19

«
...
17
18
19
20
21
...
»

Содержание SKANER A4













































Отзывы:

Нет отзывов

Похожие инструкции для SKANER A4

MultiScanner i520 OneStep

Бренд: Zircon Страницы: 3

Бренд: Z Corporation Страницы: 51

Бренд: Magtek Страницы: 2

Бренд: HOKUYO AUTOMATIC Страницы: 155

Бренд: Renkforce Страницы: 4

Бренд: Exar Страницы: 20

Бренд: Raven Страницы: 2

Бренд: Fuji Xerox Страницы: 50

Pannoramic DESK II

Бренд: 3DHISTECH Ltd. Страницы: 82

Бренд: Xerox Страницы: 203

Бренд: Radio Shack Страницы: 62

XDM5205DWU - DocuMate 520

Бренд: Xerox Страницы: 149

Бренд: Radio Shack Страницы: 40

Бренд: Uniden Страницы: 35

Бренд: Uniden Страницы: 60

Бренд: Uniden Страницы: 148

Бренд: Panasonic Страницы: 61

CanoScan FB 630U

Бренд: Canon Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды