Custom Audio Electronics MODUS3 Скачать руководство пользователя страница 33

Страница: 33 / 76

5.2

Coniguration by software

The setup parameters can be set by using the “PrinterSet” software tool available on

www.custom4u.it

For a detailed description of the device operating parameters see the following paragraphs.

To conigure the device by software, proceed as follows:

Connect the device to a PC directly

(see paragraph 3.3), without using HUB devices.

Start “PrinterSet” software tool.

Click on LOAD > FROM DEVICE and select

the device connected to the PC.

Click on SETUP to access the operating parameteres of

the device to be configured.

Click on SAVE > TO DEVICE

to make the changes made effective.

Make the desired changes to the

device operating parameters.

SETUP

FONTS

UPGRADE

SAVE

LOAD

PORT

From Device

From File

SAVE

PORT

LOAD

Click on LOAD > From ﬁle and select a .psc ﬁle on your PC

Drag and drop a .psc ﬁle

Enabled

Enabled

Disabled

Disabled

Enabled

Disabled

SETUP

Info

<Parameters>

SAVE

LOAD

PORT

To Device

To File

Disabled

Enabled

Enabled

Disabled

Enabled

Disabled

SETUP

<Parameters>

Activation of the Bluetooth® module
or WiFi on the device. If the “Wireless”
parameter is set to ON (active) do not
connect any communication cable to
the device.

SAVE

LOAD

PORT

EXTRA

Connect the device to a PC directly

(see

paragraph 3.2

), without using HUB devices.

ATTENTION:
During saving, it is strongly discouraged to disconnect the communication cable or to remove the power supply of the
PC or the device.

Содержание MODUS3













































































Результаты поиска

Содержание MODUS3

Отзывы:

Бренды по названию

Популярные бренды

Custom Audio Electronics MODUS3, Руководство пользователя

Результаты поиска

Содержание MODUS3

Отзывы:

Бренды по названию

Популярные бренды