Cushman Titan XD, Руководство пользователя

Страница: 13 / 68

1 - 7
SAFETY
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
1
LABELS AND PICTOGRAMS
606003
606003
Open door
WARNING
Do NOT
drive with
door open
Latch door
before driving
Close door
630652
630652
Fuses
2A 2A 20A
15A 15A 15A
15A 5A
5A 7.5 A
630653
1
2
3
4
5
6
7
8
9
10
630653
Fuse numbers
and sizes
Read Manual
Tow
Maintenance
Storage
Run
P
631074
631074
Forward
Neutral
Reverse
Parking
Brake Light
ON
OFF
P
630651
MAX
25%
630651
WARNING
Read the manual
Keep entire body
inside vehicle.
Turn key OFF
Set parking brake
before leaving
vehicle
Use caution in
inclement weather
Do not operate
under influence of
drugs or alcohol
Do not drive
on highway
Turn key to ON
Select Forward
direction
Press accelerator
to start movement
Cross slope
25% MAX
Turn key to ON
Select Reverse
warning indicator
will sound
Press accelerator
to start movement
MAX ramp grade
25% or 14°
600947
!
P
P
600947
MAX
2200 lbs.
1000 kg
X 4
MAX
2600 lbs.
1200 kg
X 2
WARNING
Read the manual
Danger of
explosion
DO NOT
fill fuel can
on load bed.
4 passengers Secure
load as far forward as
possible MAX weight
2200 lbs or 1100 kg
Load with high
center of gravity
may cause
tip over
Do not
ride on
deck
2 passengers Secure
load as far forward as
possible MAX weight
2600 lbs or 1200 kg
1-1 HW FAILSAFE Vehicle will not run Check motor wiring, replace controller
1-2 THROTTLE FAULT 1 Vehicle will not run Check pedal box adjustment, connections,
replace ITS
1-3 SPEED SENSOR FAULT Vehicle runs slowly Check speed sensor connection, and wiring,
replace sensor if required
1-4 HPD Vehicle will not run Release and reapply pedal. Check pedal
box, linkage, switch and key switch
1-5 MOTOR STALL Vehicle stopped Remove mechanical blockage
2-1 LOW BATTERY VOLTAGEVehicle performance reducedCharge batteries, replace bad batteries
2-2 OVERVOLTAGE Regen performance reduced Check that battery voltage is less than 60 VDC
2-3 THERMAL CUTBACK
Vehicle performance reducedAllow controller to cool
2-4 MAIN DRIVER ON
Vehicle runs slowly Solenoid driver defective, replace controller
2-5 VDD FAULT Vehicle will not run Replace controller
3-1 MAIN DRIVER OFF Solenoid does not close Replace controller
3-2 MAIN WELDED
Vehicle runs slowly Verify solenoid welded, replace solenoid
3-3 PRECHARGE FAULT Vehicle will not run Check for additional electronics attached to
B+, replace controller
3-4 FIELD MISSING
Solenoid closes, vehicle will
not run Check wiring.
Replace power harness and motor if required.
3-5 FIELD OVERCURRENT
Vehicle will not run Field windings or power harness shorted.
Verify, replace motor if necessary.
4-1 CURRENT SENSE FAULT Vehicle will not run Replace controller
4-3 M- FAULT Vehicle will not run Check M- wiring and repair, replace controller
4-4 AUX CONT DNC
Vehicle will not run Replace controller
4-5 WELDED AUX CONT Vehicle runs slowly Replace controller
5-1 EEPROM FAILSAFE Vehicle will not run Replace controller
5-2 MAIN COIL OPEN Vehicle will not run Check coil connections/wiring.
Replace solenoid if necessary
5-3 MAIN CONT DNC Vehicle will not run Check all solenoid wiring.
Replace solenoid if necessary
5-5 MISSING CONTACTOR
Vehicle stops Check all solenoid wiring.
Replace solenoid if necessary
Code Fault Code Symptoms Corrective Action
P/N 73398-G01
‹
The LED will flash a diagnostic fault code when a fault is detected
‹
Some faults may only be detected by operating the vehicle with the rear
of the vehicle raised and supported on safety stands
‹
Always turn the 'RUN TOW/MAINTENANCE' switch (located in the
battery compartment) to the 'TOW/MAINTENANCE' position before
performing any repairs or maintenance to the vehicle
‹
Select 'RUN' before returning the vehicle to service
DIAGNOSTIC FAULT CODES
73398-G01
630650
WARNING
Read the
manual
DO NOT
short across
battery terminals
WARNING
Explosive
NO
Sparks
NO
Smoking
WARNING
Corrosive
Type EE Vehicle
One label each
side of vehicle
35216G01