Cuscini ABRI Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 10

Cuscini ABRI Скачать руководство пользователя страница 1

of 10

Fixed Classic Roof / Single Rail System

ABRI

Step by Step Assembly Instructions

Assembly Requirements

Before You Begin

Two Persons
Hand Drill
Ladder
Wrench Kit
Tape Measure

These installation instructions will lead you through the process of installing your new shelter. The installation of the shelter

requires special attention to certain detail. Before you begin you should:

CHECK YOUR ORDER

. Make sure the contents of the carton match the product numbers on your order. Contact your dealer

if there are any damaged, missing or incorrect parts.

PAY ATTENTION TO SAFETY

. Because of the size and weight of certain parts, installation is recommended with no fewer

than two people. Always maintain a clean, organized work area.

MAKE SURE YOU HAVE THE RIGHT TOOLS AND MATERIALS

. Jardin de Ville supplies the appropriate fasteners upon

request through your dealer for anchoring the shelter securely to the ground. If you are unsure about the required anchoring

system best suited for your shelter, consult your dealer for the proper fastening method.

REVIEW ENTIRE INSTALLATION GUIDE

. This step gives you the opportunity to contact your dealer to answer any

questions before you begin.

Level
Rubber Hammer
Screwdriver Set

1

Model # Pavillion 1.0

Distributor: ShadeScapes Americas

970.527.7070

cuscini.shadescapesamericas.com

1
2
3
...
»

Содержание ABRI











Отзывы:

Нет отзывов