Curtiss-Wright SCRAMNet+ SC150e Скачать руководство пользователя

Страница: 60 / 140

OPERATION

5-10

S SC150e HARDWARE REFERENCE

5.7 Interrupt Controls

S SC150e allows a processor to receive interrupts from and/or transmit

interrupts to any other processors on the network, including the originating processor.

Table 5-3 indicates the various sources for interrupt control.

5.7.1 Interrupt Options

Table 5-3 Interrupt Controls

Condition Register

Description

Host Interrupt Enable

CSR0[3]

Must be set in order to receive any interrupts from the
network.

Receive Interrupt Enable (RIE)

ACR[0]

Generates an interrupt to the host from network data
received at the associated Shared Memory location.

Transmit Interrupt Enable (TIE)

ACR[1]

Generates an interrupt to the network for a host write to
the associated Shared Memory location.

Interrupt on Memory Mask Match

Enable

CSR0[5]

Permits a shared memory interrupt. Must be set in order
to receive any interrupts from the network.

Override RIE

CSR0[6]

Generates an interrupt to the host regardless of the
ACR RIE setting upon receipt of any network interrupt
message.

Enable Interrupt on Error

CSR0[7]

Generates an interrupt request as specified in the CSR9
Mask register as the corresponding bit in CSR1 is set.

Network Interrupt Enable

CSR0[8]

Permits transmission of interrupt data to the network.

Override TIE

CSR0[ 9]

Transmits Interrupt message to the network regardless
of the ACR TIE setting.

Reset Interrupt FIFO

CSR0[13]

Toggle from ‘0’ to ‘1’ to ‘0’ to reset Interrupt FIFO.

Interrupts Armed

CSR1[14]

During the interrupt operation, indicates conditions to
receive interrupt are active. If ‘0’, no interrupts will be
received by the host. Any write to CSR1 will reset to ‘1’.

Enable Interrupt on Own Slot

CSR2[10]

In conjunction with CSR2[9] enables host self-interrupt.

LSP of Interrupt Address

CSR4[15:0]

Interrupt Address A15 - A0.

MSP of Interrupt Address

CSR5[6:0]

Interrupt Address A22 - A16. Works in conjunction with
CSR4[15:0].

Interrupt FIFO Not Empty

CSR5[15]

When ‘0’, Interrupt FIFO is empty. If ‘1’, CSR5 and
CSR4 contain legitimate interrupt address(es).

Receive Interrupt Override

CSR8[10]

When set, all incoming network messages are treated
as interrupt messages.

Interrupt on Error Mask

CSR9[15:0]

Interrupts for specified error/status conditions.

PCI Interrupt Status

(See NOTE)

This register is used to report interrupt status and to
clear the interrupt.

NOTE

: PCI configuration register offset 48 [32:0]

Содержание SCRAMNet+ SC150e





























































































































Результаты поиска

Содержание SCRAMNet+ SC150e

Отзывы:

Похожие инструкции для SCRAMNet+ SC150e

Бренды по названию

Популярные бренды

Curtiss-Wright SCRAMNet+ SC150e, Справочник по аппаратуре

Результаты поиска

Содержание SCRAMNet+ SC150e

Отзывы:

Похожие инструкции для SCRAMNet+ SC150e

Бренды по названию

Популярные бренды